Cisco CCT Data Center 010-151 Questions & Answers

• Question 81:

  Up to what speed can Category 5 UTP cable transmit data?

  A. 10 Mb/s

  B. 100 Mb/s

  C. 1000 Mb/s

  D. 10000 Mb/s

  Correct Answer: B

• Question 82:

  Refer to the exhibit.

  

  This image shows a CPU Pick-and-Place tool and a CPU Socket Protective Cap Removal tool. Which types of Cisco UCS servers and Intel Xeon processors do these tools support?

  A. Cisco UCS B22 Blade Server, C22 Rack Server, and C24 Rack Sever with Intel Xeon E5-2400 Series processors

  B. Cisco UCS B22 Blade Server, C22 Rack Server, and C24 Rack Sever with Intel Xeon E5-2600 Series processors

  C. Cisco UCS B200 M3 Blade Server, B420 M3 Blade Server, C220 Rack Server, C240 Rack Sever, and C420 Rack Sever with Intel Xeon E5-2400 Series processors

  D. Cisco UCS B200 M3 Blade Server, B420 M3 Blade Server, C220 Rack Server, C240 Rack Sever, and C420 Rack Sever with Intel Xeon E5-2600 Series processors

  Correct Answer: D

• Question 83:

  Which two remote file system methods are used in the training material to transfer firmware to the Fabric Interconnect? (Choose two.)

  A. FTPS

  B. FTP

  C. TFTP

  D. RSH

  Correct Answer: BC

• Question 84:

  On which three devices can the Host Upgrade Utility be performed? (Choose three.)

  A. C420

  B. C230

  C. B230

  D. B210

  E. C210

  F. B460

  G. C240

  Correct Answer: AEG

• Question 85:

  Which three firmware components does the Host Upgrade Utility upgrade? (Choose three.)

  A. Fabric Interconnect firmware

  B. LAN on Motherboard

  C. Cisco UCS Manager

  D. CIMC

  E. System BIOS

  Correct Answer: DE

• Question 86:

  Which three troubleshooting procedures do you perform when there is no power to a Cisco UCS B250 M2 Blade Server? (Choose three.)

  A. Decommission and acknowledge the blade.

  B. Check the back of the blade to ensure that there is no damage to the connection that goes into chassis.

  C. Reseat the memory DIMMs.

  D. Check the CPU sockets for bent pins.

  E. Reseat the blade in the same slot in the chassis.

  F. Move the blade to another slot in the chassis.

  Correct Answer: BEF

• Question 87:

  Which two statements about DIMM replacement in Cisco UCS Servers are true? (Choose two.)

  A. In blade servers, DIMMs can be installed in either 1, 2, 4, or 8 DIMMs per channel.

  B. Rack-mount and blade servers have memory fault LEDs that indicate which DIMM requires attention.

  C. In servers that require pairs of DIMMs, the pairs must be identical (manufacturer, size, part #, and so on).

  D. If the memory in a server is not fully populated, you can install DIMMs in any open slot.

  Correct Answer: AC

• Question 88:

  Which three tools are necessary to console into a Cisco UCS C-Series Rack-Mount Server? (Choose three.)

  A. Cisco DB-9-to-RJ-45 console cable

  B. laptop

  C. monitor

  D. keyboard

  E. KVM dongle

  F. USB serial adapter

  Correct Answer: CDE

• Question 89:

  After installation or replacement of a Cisco UCS C-Series Rack-Mount Server, the host does not boot. Which four options should be verified? (Choose four.)

  A. Verify the power source to the equipment.

  B. Check for loose HDD cables.

  C. Reseat the DIMMs, CPU, and PCI cards.

  D. Verify that power supplies are receiving power.

  E. Reseat the mezzanine card connector.

  F. Check the CPU sockets for bent pins.

  G. Check the Cisco IMC for fan faults.

  Correct Answer: ACDF

• Question 90:

  Which three components are hot swappable in a Cisco UCS Blade Server and Chassis? (Choose three.)

  A. Fabric Extender

  B. Power supply

  C. Heat sink

  D. SAS Hard Drive

  E. 2x8GB Kit DIMMs

  F. Mezzanine card

  Correct Answer: ABD