Scenario: A customer logged in as a user with superuser access rights and is making configuration changes on a NetScaler HA pair. After a few minutes, the customer notices that the changes are NOT visible on the GUI or CLI.
What is the customer doing incorrectly?
A. The customer is not using the nsroot account.
B. The customer has enabled fail safe on both nodes.
C. The customer is making changes on the primary node.
D. The customer is making changes on the secondary node.
Scenario: An administrator has set up a NetScaler in HA mode and now wants to bind the SSL certificate to one of the SSL virtual servers. However, the administrator notices that the command failed on the secondary node while succeeding on the primary node. Both nodes in HA are healthy, with successful configuration synchronization and command propagation.
Which reason explains the command failure on the secondary node?
A. Command syntax is not correct.
B. Command not executed with root ID.
C. SSL command not available on secondary node.
D. SSL certificate is not present on secondary node.
An administrator set up a NetScaler pair in HA but noticed that the secondary node status is showing as DOWN.
Which two configurations should be made on the secondary node to bring the node status to UP in HA, according to best practices? (Choose two.)
A. Disable unused interfaces.
B. Disable HAMON on disabled interfaces.
C. Configure nsroot password to be identical for both nodes.
D. Configure RPC node password to be identical for both nodes.
An administrator set up a NetScaler pair in HA but later noticed that the configuration changes made on the primary node were NOT synchronized with the secondary node.
Which configuration setting must be corrected for successful configuration synchronization between both nodes in HA mode?
A. HA monitoring on interfaces is set to off.
B. HA monitoring on the node IDs is set to off.
C. nsroot password is not identical for both nodes.
D. RPC node password is not identical for both nodes.
Scenario: An administrator set up a NetScaler in an HA configuration. When the Primary node was rebooted due to a power failure, the failover did NOT occur as expected.
Which configuration settings must have prevented the failover in the above scenario?
A. Primary node is set to fail-safe mode.
B. Primary node is set to stay secondary.
C. Secondary node is set to do not failover.
D. Secondary node is set to stay secondary.
Scenario: An administrator plans to set up a NetScaler in an HA configuration. The two nodes in the HA pair are located on two separate networks.
Which setting must the administrator configure on each node to ensure that both nodes in the HA pair can synchronize configuration and propagate commands?
A. Add static route for remote node network
B. Add route monitor for remote node network
C. Turn on Independent Router Configuration (IRC)
D. Turn on Independent Network Configuration (INC) mode
Scenario: An administrator plans to set up a NetScaler in HA mode. One of the requirements for the environment is to ensure that traffic is handled in the most reliable way even if both nodes in HA are unhealthy or partially fail.
Which setting must the administrator configure to ensure the traffic is handled in the most reliable way, even if both nodes in HA are unhealthy?
A. AutoFail
B. FailSafe
C. FailActive
D. Force Failover
Which type of SNMP trap would allow for an administrator to specify a minimum level of severity of events?
A. Public
B. Private
C. Generic
D. Specific
Scenario: An administrator has configured an SNMP manager to allow an engineer with the IP address
192.168.1.1 to perform SNMP queries on the NetScaler appliance. However, the engineer has been promoted to another position and has delegated SNMP management to another engineer who will manage the box from 192.168.1.5.
Which two steps are required for the administrator to allow the new engineer to manage the box? (Choose two.)
A. Add SNMP Manager 192.168.1.5.
B. Add SNMP Community 192.168.1.5.
C. Remove SNMP manager 192.168.1.1.
D. Remove SNMP Community 192.168.1.1.
When leveraging the Dashboard, which information would indicate to an administrator that server performance has been improved after enabling caching in a network environment?
A. Client connection count increases
B. Server-side request rate increases
C. Client connection count decreases
D. Server-side request rate decreases
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Citrix exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 1Y0-A21 exam preparations and Citrix certification application, do not hesitate to visit our Vcedump.com to find your solutions here.