A network engineer is troubleshooting a situation where ARP requests for IPs in other subnets (for
example 10.192.12.80) are appearing in the 10.192.8.0/24 subnet.
Which command could the engineer run on the NetScaler to verify IP to VLAN bindings?
A. show ip
B. netstat -r
C. show arp
D. show vlan
Scenario: An engineer needs to configure a monitor to ensure that each server is tested every 10 seconds and requires that the server pass the test four consecutive times before marking a server as UP. If the test fails, the server should be marked as down for 60 seconds.
To configure the monitor, the engineer should configure an interval of 10 seconds, down-time of 60 seconds; __________ as 4; and retries as __________. (Choose the correct set of options to complete the sentence.)
A. failure retries; 1
B. failure retries; 4
C. success retries; 1
D. success retries; 4
Scenario: A network engineer has configured an HTTP application to be load balanced using a virtual server named Svr1. Users have reported intermittent errors and the engineer has been given the client IP address of an affected user and asked to determine which back end service they are connected to.
Using the command-line interface, how could the engineer find this information?
A. Show lb vServer Svr1
B. Show system session
C. Show lb vServer Svr1 -Summary
D. Show lb persistentSessions Svr1
A network engineer should use a HTTP-ECV monitor type to control the status of a load balanced web server resource when __________. (Choose the correct option to complete the sentence.)
A. checking for multiple HTTP response codes
B. wanting to use a customized HTTP Request
C. checking for a specific pattern in the HTTP Response body
D. checking for a specific pattern in the HTTP Response header
Scenario: A network engineer has installed a NetScaler system into their corporate DMZ and would like to provide access to a web server on the internal LAN. The web server will be accessed by external users through the NetScaler. The firewall administrator has opened the relevant ports required on the external and the internal firewall.
The engineer notices that the virtual server and services representing the web server are down and the internal web server does NOT appear accessible from the NetScaler.
What could be the cause of this?
A. USIP is not enabled.
B. Client IP Insertion is not enabled.
C. A URL rewrite policy is not created.
D. A SNIP address has not been added.
NSROOT is the only account configured with super user rights.
In order to initiate the password recovery procedure, the engineer must __________. (Choose the correct option to complete the sentence.)
A. logon using SCP and modify ns.conf
B. connect to the physical NetScaler device
C. connect using SSH to the NetScaler device
D. logon using nsrecover/nsroot and reallocate licenses
Scenario: A network engineer suspects that there is a duplex mismatch in the network configuration. The NSIP address is 10.10.1.206.
How can the administrator verify the configuration in this scenario?
A. Run the 'netstat -r' command.
B. Run the show IP 10.10.1.206 command.
C. Run the start nstrace -level 10 command.
D. Check for the interface configuration in the GUI.
Scenario: Primary NetScaler (NS1) is licensed for 10000 Maximum ICA users and 305 Access Gateway users. Secondary NetScaler (NS2) is licensed for 10000 Maximum ICA users and five Access Gateway users. From where and which command should a network engineer run to display diagnostics on the
licenses?
A. From the shell, run 'view license'.
B. From the shell, run 'more /var/log/license.log'.
C. From the command-line interface, run 'show license'.
D. From the command-line interface, run 'cat /var/log/license.log'.
How could an engineer configure a monitor to ensure that a server is marked as DOWN if the monitor test is successful?
A. Enable the LRTM option for the monitor
B. Enable the Reverse option for the monitor
C. Disable Down state flush for the service group
D. Disable the Health monitoring option for the service group
Scenario: A network engineer created an SSL virtual server and enabled smart card on it. The engineer tried browsing to the server and noticed the back-end system could NOT see the users certificates.
What could be causing this issue?
A. The SSL virtual server cannot forward a client certificate.
B. The network engineer has not set smart card to mandatory.
C. The SSL virtual server cannot use smart card authentication.
D. The network engineer has not enabled SNI on the virtual server.
E. The network engineer forgot to enable the SSL policy allowing smart card forwarding on the SSL virtual server.
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Citrix exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 1Y0-351 exam preparations and Citrix certification application, do not hesitate to visit our Vcedump.com to find your solutions here.