Citrix CCP-N 1Y0-351 Questions & Answers

• Question 161:

  On which two types of virtual servers is the SOURCEIP persistence type supported? (Choose two.)

  A. HTTPS

  B. RTSP

  C. SSL_Bridge D. SIP_UDP

  Correct Answer: AC

• Question 162:

  Which three command-line interface commands should a NetScaler Engineer execute to configure an authentication virtual server? (Choose three.)

  A. add authentication vserver ssl

  B. bind ssl certkey

  C. set authentication vserver -authenticationDomain

  D. show authentication vserver

  E. add ssl certkey

  Correct Answer: ABC

• Question 163:

  Which public IP address must a NetScaler Engineer set on a NetScaler appliance to allow for client connections?

  A. NSIP

  B. SNIP

  C. VIP

  D. USNIP

  Correct Answer: C

• Question 164:

  Which two virtual servers could a NetScaler Engineer configure to redirect GET requests to application servers? (Choose two.)

  A. Load balancing

  B. Authentication

  C. Wildcard

  D. Content switching

  Correct Answer: AD

• Question 165:

  Which NetScaler IP address must a NetScaler Engineer set for management and general system access purposes?

  A. NSIP

  B. SNIP

  C. VIP

  D. USNIP

  Correct Answer: A

• Question 166:

  Which client c the NetScaler may use?

  A. Accept

  B. User-Agent

  C. Content-Type

  D. Accept-Encoding

  Correct Answer: D

• Question 167:

  Which option must a NetScaler Engineer set to enable client keep-alive mode?

  A. -cka yes

  B. -usip yes

  C. -cip disabled

  D. -useproxyport yes

  Correct Answer: A

• Question 168:

  Scenario: A NetScaler Engineer creates a new HTTP VServer using the following command:

  add lb vserver lb_test HTTP 172.20.10.85 80 -lbMethod LEASTCONNECTION -persistencetype COOKIEINSERT -timeout 0 -authentication ON -cacheable YES

  During testing, the engineer notices a cookie named NSC_iuuq2 with a value of: ffffffff020a1d1545525d5f4f58455e445a4a423660

  What is the purpose of this cookie?

  A. It indicates that the client has been authenticated.

  B. It indicates that the client has NOT been authenticated.

  C. It is used for persistence, describing only the VServer ID and Service IP.

  D. It is used for persistence, describing the VServer ID, Service IP and Service Port.

  Correct Answer: D

• Question 169:

  Scenario: A NetScaler Engineer has a high-availability (HA) pair of NetScaler MPX devices (NS1 and NS2)

  connected on interfaces 0/1, 1/1 and 1/2. NS1 is currently the primary unit. Fail-safe mode is NOT enabled.

  High-availability monitor is enabled on all the connected interfaces. The engineer sees the following line in

  the output of his "show node" command from the command-line interface:

  Interfaces on which heartbeats are not seen: 1/1 1/2

  Interfaces causing Partial Failure: None

  What will happen if the 0/1 interface fails?

  A. NS1 and NS2 will both become primary.

  B. NS2 will fail and NS1 will remain primary.

  C. NS1 will fail and NS2 will become primary.

  D. NS1 and NS2 will both fail and become secondary.

  Correct Answer: A

• Question 170:

  Scenario: An engineer has been given the task of selecting the TCP profile for a NetScaler appliance. The appliance has a 1.5Mbit WAN interface that has considerable and intermittent packet loss.

  Which TCP profile should the engineer choose to optimize traffic for the WAN interface?

  A. nstcp_default_profile

  B. nstcp_default_tcp_lfp

  C. nstcp_default_tcp_lnp

  D. nstcp_default_tcp_lan

  Correct Answer: C