Oracle Oracle Certifications 1Z0-404 Questions & Answers

• Question 61:

  You used the no command to delete a configuration element.

  Whichstatement is true?

  A. The deletion is lost on immediate reboot.

  B. The deletion is reflected when viewing the running configuration.

  C. The deletion takes effect immediately in the saved configuration.

  D. The deletion always requires a reboot to take effect.

  E. The deletion requires auto-save enabled.

  Correct Answer: A

• Question 62:

  Examine the output below from the show sipd invite command:

  

  How many 600 Busy Everywhere messages sent by the Session Border Controller in the last 140 seconds did not originate from a downstreamdevice?

  A. 157

  B. 13

  C. 4

  D. 161

  E. 0

  Correct Answer: B

• Question 63:

  Which three statements are true about the bootloader? (Choose three.)

  A. It decompresses the image file and loads it into the main RAM

  B. It reads the imagefile

  C. It is based on Linux

  D. It looks at the boot parameters

  E. It is a Windriver's VxWork product

  Correct Answer: ABD

• Question 64:

  To ensure proper operation of a Session Border Controller HighAvailability (HA) pair, it is critical that both of the devices can originate legitimate traffic on media interfaces independent of the network interface IP address.

  How is this type of traffic accommodated?

  A. by setting the pri-utility-addr, sec-utility-addr, and sec-gateway values to addresses in the same subnet as the IP address configured on the management interfaces

  B. by setting the pri-utility-addr, sec-utility-addr, and sec-gateway values to addresses in the same subnet as the IP address configured on the media interfaces

  C. by setting the utility address and sec-gateway values to addresses in different subnets as the IP address configured on the wancom interfaces

  D. by setting a unique address on the wancoml and wancom2 interfaces via the utilityaddress command

  E. via the utility address parameters on the wancoml and wancom2 interfaces

  Correct Answer: A

• Question 65:

  Where are passwords and licensing information stored?

  A. Non-Volatile Random Access Memory (NVRAM)

  B. Content Addressable Memory (CAM)

  C. RAMmemory

  D. Synchronous Dynamic Random Access Memory (SDRAM)

  E. Boot Flash

  Correct Answer: A

• Question 66:

  View the Exhibit.

  

  Which statement is true about this output of the show health command?

  A. The two nodes have different health scores.

  B. The training1 peer is the standby node.

  C. The switchover berpd force commandwas executed to do a manual failover.

  D. The training6 peer is the active node.

  E. The training6 peer will wait 1050 ms before considering the training1 peer out of service.

  Correct Answer: E

• Question 67:

  CORRECT TEXT

  Which statement is true about the Host In Path (HIP) feature In the Session Border Controller?

  A.

  Correct Answer: A

  Answer: By default, theSession Border Controller's FTP, ICMP, SNMP, and Telnet services cannot be accessed via the management interfaces. Answer: To enable these services (FTP ICMP, SNMP, and Telnet services), the enable host-in-path command must be executed from the superuser mode. Answer: To enable these services, the Session Border Controller includes a software license that enables administrative traffic over the media interfaces. Answer: By default, the Session Border Controller's FTP, ICMP, SNMP, and Telnet services cannot be accessed viathe media interfaces. Answer: These four fields (FTP, ICMP, SNMP, and Telnet services) are collectively known as the Host Interface Priority.

  Reference https://docs.oracle.com/cd/E52358_01/doc/sbc_scx620_acliconfiguration.pdf

• Question 68:

  You are adding peers to a Policy-Based Realm Bridging (PBRB) configuration.

  Which two configuration steps, among others, are required? (Choose two.)

  A. Navigate to the media-manager configuration branch and configure the realm-config configuration element.

  B. Navigate to the session-router configuration branch and configure the sipd-address configuration element.

  C. Navigate to the session-router configuration branch and configure the local-policy configuration element.

  D. Navigate to the session-router configuration branch and configure the sip-nat configuration element.

  E. Navigate to the media-manager configuration branch and configure the access-control configuration element.

  Correct Answer: AE

• Question 69:

  Which two statements describe the functions of Session Border Controllers? (Choose two.)

  A. they replace typical edge routers and firewalls in order to provide a unified network border forsignaling and media control

  B. they are session-aware devices that enable control of end-to-end interactive communications across IP network borders

  C. they are based on the Windows operating system

  D. they provide routing functions for IP, TCP, and SMTPusing application parameters

  E. they provide signaling proxy functions for SIP, H.323, and MGCP, which includes access control, signaling constraints, and topology hiding

  Correct Answer: AE

• Question 70:

  Which three options are valid ways to apply Header Manipulation Rules (HMRs) to your existing configuration?

  A. Navigate to the network-interface configuration element and configure the in- manipulationid parameter.

  B. Navigate to the session-agent configuration element and configure the in-manipulationid parameter.

  C. Navigate to the sip-interface configuration element and configure the in-manipulationid parameter.

  D. Navigate to the session-agent configuration element and configure the in-manipulationid parameter.

  E. Navigate to the session-group configuration element and configure the in-manipulationid parameter.

  Correct Answer: ABC