Riverbed Riverbed Certifications 299-01 Questions & Answers

• Question 81:

  Which filter should be used to analyze a capture job within Cascade Pilot?

  A. Use a BPF filter to speed up the View.

  B. Apply a generic View and then define a filter by drilling-down through a more specific View.

  C. Use a Cascade Pilot filter first and then a BPF filter.

  D. Create a time filter and then apply a View with a Cascade Pilot filter.

  Correct Answer: D

• Question 82:

  To install Cascade Shark, the best practice to initially configure the IP Address to be used on the network is:

  A. Connect a cross-over cable from your laptop to the Ethernet management port and connect through the Web browser to the default IP Address of 192.168.1.10.

  B. Connect a cross-over cable from your laptop to the Auxiliary Ethernet port and connect through the Web browser to the default IP Address of 192.168.1.10.

  C. Connect by KVM or Serial Console and run the command line tool, sa_wizard, to perform the initial configuration.

  D. Connect to the appliance using the Riverbed Central Management Console (CMC) on its default IP Address and perform the initial configuration.

  Correct Answer: C

• Question 83:

  A SPAN port is often limited in which way:

  A. Can only capture traffic from a single port.

  B. Can only capture traffic that is routed (not switched)

  C. Can only capture traffic that is ingress or received by the device

  D. The number that can be configured is oftentimes limited to two

  E. Requires at least two monitoring ports to capture a single link

  Correct Answer: D

• Question 84:

  How many signatures can a Layer-7 Fingerprint have?

  A. 1

  B. 2

  C. 5

  D. 8

  E. 10

  Correct Answer: E

• Question 85:

  What is the chart granularity possible through the Cascade Pilot UI? (Select 2)

  A. 1 second on a local System, 10 milliseconds on Cascade Sharks.

  B. 1 millisecond for any View.

  C. 1 millisecond for specific Views.

  D. Generally minimum 1 second, maximum 1 day.

  Correct Answer: CD

• Question 86:

  Which of the following is information that Netflow v5 provides to the Cascade solution? (Select 2)

  A. End time of Flow

  B. Source MAC address

  C. Layer 4 Protocol Type

  D. TCP Checksum Validation Result

  Correct Answer: AC

• Question 87:

  Hosts that do not match group definitions within a group type are:

  A. Placed in an unassigned group.

  B. Not placed into a group within the group type.

  C. Not allowed

  D. Flagged as an error.

  E. Likely to cause errors in the future.

  Correct Answer: B

• Question 88:

  On the Cascade Shark Appliance, which User Groups on the appliance exist by default:

  A. Administrators, Operators, Monitors

  B. Read-Only-Group, Read-Write-Group, Full-Access Group

  C. Administrators, Network-Operations, Network-Security

  D. Administrators, NormalUsers, Viewers

  E. Administrators, Operators, Monitors, Viewers

  Correct Answer: D

• Question 89:

  How are trace clips created in Cascade Pilot? (Select 2)

  A. Select a Capture Job, right-click, and select "Create Trace Clip".

  B. Drag a bar from a Bar Chart to the Capture Job.

  C. Click the + button in the Capture Job item and select a time window.

  D. Select a time window and apply a Cascade Pilot filter.

  Correct Answer: AC

• Question 90:

  What best describes the Rebalance and Reallocate buttons on the Configuration/Flow Log page of the Cascade Profiler? (Select 2)

  A. Rebalance moves flows among analysers in a Cascade Enterprise Profiler.

  B. Reallocate varies the storage space dedicated for templates and saved reports.

  C. Rebalance optimizes the use of the allocated space that allows you to get a longer retention time out of the same amount of disk space.

  D. Reallocate allows the users to decide the percent of total disk storage capacity that is allocated to the various flow logs.

  E. Rebalancing and Reallocating must be done simultaneously.

  Correct Answer: CD