Riverbed Riverbed Certifications 830-01 Questions & Answers

• Question 111:

  When deploying Interceptor appliances on aggregated links, you must: (Select 2) A. configure each in-path interface to have a unique IP address

  B. configure WCCP

  C. configure the allow neighbor failure command

  D. configure each in-path interface to have the same IP address

  E. configure the no arp filter response command

  Correct Answer: AE

• Question 112:

  On the Interceptor appliance, the Networking > Steelheads page displays which of the following?

  A. Optimized connections, Admission Control connection count.

  B. Optimized connections, Pass-through connections count.

  C. Current Connections per Second (CPS), Admission Control count.

  D. Packets per Second, Connections per Second, Optimized connections count.

  Correct Answer: A

• Question 113:

  In the Interceptor appliance version 3.0 and later the command to enable cluster failover is:

  A. failover-peer enable.

  B. Interceptor appliance communication allow-failure enable.

  C. Interceptor appliance failover enable.

  D. Enable interceptor appliance peer failover.

  Correct Answer: B

• Question 114:

  What is the primary purpose of enabling Multiple Interface Support on the Interceptor appliance?

  A. It allows for the ability to support multiple NICs on the Interceptor appliance.

  B. It allows the Interceptor appliance to communicate with Steelhead appliances and other Interceptor appliances using more than one in-path interface.

  C. It allows the Interceptor appliance to communicate using multicast to in-path interfaces on the Steelhead appliances.

  D. It allows the Interceptor appliance to be managed by in-path interfaces as well as the primary interface.

  Correct Answer: B

• Question 115:

  On an Interceptor appliance running Fair Peering v2, what Steelhead characteristic is used to calculate peer affinity?

  A. Appliance size.

  B. Percentage of data store free.

  C. Maximum connection count.

  D. Version of RiOS running.

  Correct Answer: A

• Question 116:

  Adaptive data streamlining provides you:

  A. with the ability to fine tune the data streamlining capabilities, and enables you to obtain the right balance between optimal bandwidth reduction and optimal throughput

  B. with the ability to fine tune the data streamlining capabilities, and enables you to obtain the right balance between optimal bandwidth reduction and optimal acceleration

  C. with the ability to fine tune the compression capabilities, and enables you to obtain the right balance between optimal bandwidth reduction and optimal throughput

  D. with the ability to fine tune the compression capabilities, and enables you to obtain the right balance between optimal bandwidth reduction and optimal acceleration

  Correct Answer: A

• Question 117:

  RiOS v7.0 and later the Steelhead Appliance can use HTTP stream splitting to optimize two different live video technologies: (Select 2)

  A. Microsoft Silverlight.

  B. Adobe HTTP Dynamic Streaming.

  C. Youtube.com video.

  D. Adobe Flash.

  Correct Answer: AB

• Question 118:

  The adaptive data streamlining settings are:

  A. Default , RiOS SDR- L, RiOS SDR-M

  B. Default , RiOS DSR- Adaptive, RiOS DSR-M

  C. Default , RiOS SDR- Adaptive, RiOS SDR-M

  D. Default , RiOS SDR- Adaptive, RiOS SDR-L

  E. RiOS SDR- Adaptive, RiOS SDR-L, RiOS DSR-M

  Correct Answer: C

• Question 119:

  RiOS v7.0 and later, the packet-mode-optimization feature can: (Select 2)

  A. optimize TCP IPv6

  B. optimize UDP IPv6

  C. optimize UDP IPv4

  D. optimize TCP IPv4

  Correct Answer: AC

• Question 120:

  What differences are there between upgrading an active VSP configuration from Steelhead EX v1.0 to Steelhead vEX 2.0 and installing a fresh Steelhead EX v2.0 appliance? (Select 2)

  A. VM slots need to be converted after an upgrade.

  B. The ESXi installation wizard must be run on a fresh install.

  C. It is possible that VM slots are not compatible with Steelhead EX v2.0 after an upgrade due to use of data flow.

  D. VMs need to be uploaded to the Steelhead during a fresh install.

  Correct Answer: AC