What is the result if one or more source (R1) devices in an SRDF/S consistency group cannot propagate data to their corresponding target (R2) devices?
A. RDF daemon trips the con-group, thereby suspending data propagation from all R1 devices in the consistency group.
B. Target (R2) devices will be Read/Write enabled at the R2 site.
C. PowerPath suspends data propagation to the R1 devices in the consistency group (trip the con-group).
D. RDF daemon suspends the data propagation from the affected R1 devices while maintaining consistency among the remaining devices.
Under which conditions will Enginuity remove the Consistency Exempt attribute from the RDF mirror?
A. Creating RDF pairs
B. Splitting RDF pairs
C. Moving RDF pairs
D. Suspending RDF pairs
How does Enginuity Consistency Assist (ECA) differ from PowerPath?
A. ECA suspends I/O at the Symmetrix level; PowerPath suspends I/O at the host level.
B. ECA suspends I/O at the host level; PowerPath suspends I/O at the Symmetrix level.
C. ECA cannot suspend I/O for multiple hosts, but PowerPath can.
D. ECA supports TimeFinder/Clone only; PowerPath supports TimeFinder/Clone and TimeFinder/Snap.
An SRDF failover operation has been executed during the testing phase of an implementation. What is the expected status of the R1 and R2 devices after performing an SRDF failover operation?
A. R1 and R2 Not Ready
B. R1 Read/Write; R2 Read/Write
C. R1 Write Disabled; R2 Read/Write
D. R1 Read/Write; R2 Write Disabled
TimeFinder/Snap virtual devices will be used as the control devices in an Open Replicator implementation. What should be the state of the virtual devices to create an Open Replication session?
A. Held
B. Not Ready
C. Read Write
D. Write Disabled
Which document should a EMC customer consult if there are questions about a system design during an SRDF/A engagement?
A. Configuration Guide
B. Level of Effort
C. Practitioner's Guide
D. Scope Document
Which UNIX utility or tool would you use to perform an HP-UX host-based data migration?
A. migratepv
B. pvmove
C. vxmigrate
D. vxevac
What is the result of performing a TimeFinder/Mirror consistent split operation against a device group?
A. All BCV devices in the group are consistent point-in-time copies.
B. All standard devices in the group are consistent point-in-time copies.
C. BCV devices are write-disabled and ready for synchronization with standard devices.
D. All standard devices are write-disabled and ready for synchronization with BCV devices.
In a single-hop SRDF/AR setup the options have been set as follows: Cycle Time=300 Delay Time=0 Overflow=Next The symreplicate session was started at time 0. The actual cycle time was 450 seconds. How many seconds after the start of the first cycle will the next cycle start?
A. 600
B. 300
C. 450
D. 900
An SRDF/A session are active, and the device pairs are in a consistent state. What will happen if there is a temporary loss of all links?
A. RPO will increase.
B. SRDF/A will drop.
C. Devices will go into Synchronous mode.
D. Devices will go into a Partitioned state.
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only EMC exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your E20-377 exam preparations and EMC certification application, do not hesitate to visit our Vcedump.com to find your solutions here.