Exam Details

  • Exam Code
    :JN0-102
  • Exam Name
    :Internet Associate, Junos(JNCIA-Junos)
  • Certification
    :Juniper Certifications
  • Vendor
    :Juniper
  • Total Questions
    :419 Q&As
  • Last Updated
    :Mar 06, 2025

Juniper Juniper Certifications JN0-102 Questions & Answers

  • Question 121:

    What represents the decimal equivalence of 01101110?

    A. 90

    B. 96

    C. 110

    D. 118

  • Question 122:

    What is the purpose of a network mask?

    A. It is used in conjunction with the wildcard mask to determine the number of hosts on a network.

    B. It is used to define which parts of the IP address are allocated to host addresses and network prefixes.

    C. It is used to hide subnets from external networks by masking the subnets with NAT.

    D. It is used to differentiate a network as a classful network or a classless network.

  • Question 123:

    You must segment your internal /24 network into a minimum of 12 subnets, each containing a minimum of 12 hosts.

    Which network mask do you use?

    A. /26

    B. /27

    C. /28

    D. /29

  • Question 124:

    -- Exhibit -user@router# run show interfaces terse Interface Admin Link Proto Local fe-0/0/0 up up fe-0/0/0.0 up upinet 10.0.39.2/24 iso mpls fe-0/0/1 up up fe-0/0/1.0 up upinet 10.0.18.2/24 fe-0/0/1.5 down up inet 10.0.19.2/24 -- Exhibit -An administrator is unable to ping any address on the 10.0.19.0/24 subnet. To identify the problem, the

    administrator uses the command shown in the exhibit. Which step should be taken to solve the problem?

    A. Check the physical cable.

    B. Issue the command activate interfaces fe-0/0/1.5.

    C. Issue the command delete interfaces fe-0/0/1.5 disable.

    D. Reconfigure the IP address.

  • Question 125:

    You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?

    A. The count parameter creates a counter that you can view with the show firewall command.

    B. The count parameter allows the router to count the number of pings for logging purposes.

    C. The count parameter allows the router to pause for 1000 seconds before sending out a ping.

    D. The count parameter allows the router to send out 1000 pings and then stop.

  • Question 126:

    -- Exhibit -[editsnmp]

    user@router# show

    communityCommunityA {

    authorization read-only;

    clients {

    192.168.1.0/28;

    }

    }

    trap-groupgroupA {

    categories {

    link;

    }

    targets {

    192.168.100.1;

    192.168.200.1;

    }

    }

    -- Exhibit -

    Referring to the exhibit, what is the purpose of the targets section of the configuration?

    A. It defines which devices will be sending traps.

    B. It specifies where to send traps.

    C. It defines the IP addresses of management systems that can access the device.

    D. It specifies which devices can be polled for SNMP data.

  • Question 127:

    -- Exhibit -user@router> show route protocol static inet.0: 12 destinations, 12 routes (12 active, 0 holddown, 0 hidden)

    + = Active Route, - = Last Active, * = Both 192.168.1.128/27 *[Static/5] 00:03:13 >to 10.20.106.10 via fe-0/0/5.1

    192.168.1.144/29 *[Static/5] 00:03:13 >to 10.20.14.131 via ge-0/0/0.0 192.168.1.192/27 *[Static/5] 00:03:13 >to 10.18.1.1 via ge-0/0/1.0 192.168.1.128/28 *[Static/5] 00:01:06 >to 10.20.14.130 via ge-0/0/0.0 -- Exhibit -Given the routing entries shown in the exhibit, which next-hop IP address will be used for the destination IP

    address 192.168.1.142? (Assume that only static routes are available for the destination.)

    A. 10.20.106.10

    B. 10.20.14.131

    C. 10.18.1.1

    D. 10.20.14.130

  • Question 128:

    Which three steps are part of the root password recovery process? (Choose three.)

    A. Reboot the device.

    B. Run the recovery script.

    C. Reset the root password.

    D. Reset the user passwords.

    E. Load factory-default configuration.

  • Question 129:

    What is the default protocol preference for OSPF internal routes?

    A. 10

    B. 15

    C. 150

    D. 160

  • Question 130:

    Which two can be used to create and apply an export policy that advertises static routes to RIP neighbors? (Choose two.)

    A. set protocols rip export demo

    B. edit policy-options policy-statement demoset term 1 from protocol staticset term 1 then accept

    C. edit policy-options policy-statement demoset term 1 from protocol static accept

    D. set protocols rip group internal export demo

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Juniper exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your JN0-102 exam preparations and Juniper certification application, do not hesitate to visit our Vcedump.com to find your solutions here.