1. Home
  2. Juniper
  3. JN0-321

DX, Associate(JNCIA-DX)

Exam Details

  • Exam Code
    :JN0-321
  • Exam Name
    :DX, Associate(JNCIA-DX)
  • Certification
    :JNCIA
  • Vendor
    :Juniper
  • Total Questions
    :166 Q&As
  • Last Updated
    :Dec 18, 2024

Juniper JNCIA JN0-321 Questions & Answers

  • Question 1:

    Which two authentication protocols can be configured for RIP on an ERX Edge Router?

    A. PAP

    B. MD5

    C. CHAP

    D. Clear text

  • Question 2:

    In a Bridged 1483 network, you suspect ATM interface 6/2.1 is receiving cells but May not be transmitting them. The interface has an ATM PVC configuration of atm pvc 33 0 33 aa15snap. How do you baseline this interface and display recent ATM cell statistics?

    A. baseline atm vc atm 6/2 1show atm vc atm 6/2 1 delta

    B. baseline atm vc atm 6/2 33show atm vc atm 6/2 33 delta

    C. baseline atm vc atm 6/2 1show atm vc atm 6/2 1 delta

    D. baseline atm vc atm 6/2 33show atm vc atm 6/2 33 delta

  • Question 3:

    What are three characteristics of RIPv2?

    A. supports VLSM

    B. SUPPORTS KERBEROS AUTHENTICATION

    C. IS BACKWARD COMPATIBLE WITH RIPv1

    D. Multicasts messages to RIP neighbors E. Uses Hello Protocol for neighbor discovery

  • Question 4:

    A RIPv1 Response message includes which of the following fields?

    A. gateway address

    B. next hop address

    C. neighbor address

    D. destination address

  • Question 5:

    Your ERX E dge Router is constantly going to a boot##prompt. What is the most likely cause for this condition?

    A. bad SRP

    B. low voltage

    C. bad midplane

    D. corrupted flash

    E. bad line module

  • Question 6:

    Which command is used to execute a macro called setup.mac?

    A. macro setup

    B. macro setup.mac

    C. run macro setup

    D. run macro setup.mac

  • Question 7:

    Which configuration command is used to make the ERX Edge Router an NTP server?

    A. set ntpserver

    B. set ntp server

    C. ntpserver enable

    D. ntp server enable

  • Question 8:

    Which command generates a BERT test pattern of alternating ones and zeros on T1number 1 for oneminute?

    A. t1 1 bert pattern alt01 interval 1

    B. t1 1 bert pattern alt01 interval 60

    C. t1 1 bert pattern alt01 interval 1

    D. t1 1 bert pattern alt01 interval 60

  • Question 9:

    Which command displays the result of a loopback test you executed on a CT3 line module in slot 5, port 0,t1 number 4?

    A. show interface 5/0:4

    B. show interface 5/0:4/1

    C. show controllers t3 5/0:4

    D. show controllers t3 5/0:4/1

  • Question 10:

    Which configuration command removes all log filters currently configured on the ERXEdge Router?

    A. no log here

    B. no log fields

    C. no log filters

    D. no log severity

Related Exams:

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Juniper exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your JN0-321 exam preparations and Juniper certification application, do not hesitate to visit our Vcedump.com to find your solutions here.