IBM IBM Certified System Administrator - AIX V1 C9010-022 Questions & Answers

• Question 241:

  The cfgmgr command appears to be taking an excessive time to complete. The administrator was able toquit the command and return to the command prompt. The administrator does not have access to the managing HMC and unable to check for any LED codes.

  How else can the cause of the observed delay be determined?

  A. Review the latest entry within /var/log/cfgdb.out.

  B. Start the syslog daemon before re-issuing the command.

  C. Re-issue the command with the W flag.

  D. Initiate the ledmon command from a separate session, then re-issue cfgmgr.

  Correct Answer: C

• Question 242:

  Prior to performing a firmware upgrade on a POWER7 system managed by an HMC. which additional component needs to be verified?

  A. HMC firmware level using the IBM Power code matrix website

  B. Available disk space on HMC.

  C. Remote Command Execution capability on the HMC.

  D. Inventory Scout ports allowed on HMC firewall.

  Correct Answer: C

• Question 243:

  What option will boot an LPAR directly from DVD media, without any user interaction required, when starting the LPAR from the Hardware Management Console (HMC)?

  A. Normal

  B. Diagnostic with default boot list

  C. System management services

  D. Open firmware OK prompt

  Correct Answer: B

• Question 244:

  What is a mandatory requirement to allow an AIX 7-based NIM Master to install clients over IPv6?

  A. The NIM Master must use static IPv6 addresses.

  B. The NIM Master must have both IPv4 and IPv6 connectivity.

  C. The NIM Master must be installed with the AIX Enterprise Edition license.

  D. The NIM Master must be running at least AIX 7.1 TLOO Service Pack3 or later.

  Correct Answer: A

• Question 245:

  What infrastructure is necessary to support update installation to an existing IVM instance?

  A. Hardware Management Console

  B. Systems Director Management Console

  C. IBM Systems Director

  D. Network Install Manager

  E. Cluster Systems Manager

  Correct Answer: D

• Question 246:

  What is a requirement for Live Partition Mobility?

  A. The network and disk must be virtual.

  B. The disk must be virtual and a Logical Host Ethernet Adapter (LHEA) for network.

  C. The client partition must be connected to a SAN.

  D. The client partition must be set up asa 'Mover Service Partition'.

  Correct Answer: A

• Question 247:

  Before changing virtual memory settings, how can an administrator check the valid range of values for a tuning parameter?

  A. Iscfg-T

  B. Isattr-R

  C. vmtune-l

  D. vmo-L

  Correct Answer: D

• Question 248:

  A system that will be re-installed has the following characteristics:

  

  If the following target_disk_data stanza is defined in the bosinst.data file used for the install, which disk will be installed with the operating system?

  target_disk_data:

  LOCATION = 0006bf1c3d817913

  SIZE_MB =

  HDISKNAME = hdisk1

  A. hdisk0

  B. hdisk1

  C. hdisk2

  D. hdisk3

  Correct Answer: C

• Question 249:

  A system dump has been initiated on an LPAR and LED code "0c1" is displayed, indicating an I/O error. Where can the administrator find out more about this error?

  A. The HMC Service Guide

  B. The AIX Version 7.1 Commands Reference

  C. HMC Event Log

  D. IBM's Fix Central under Power Systems LED support page

  Correct Answer: D

• Question 250:

  A DLPAR memory operation was attempted and failed. Given the following information, what is the likely caused A. Source LPAR is using all of its allocated memory

  

  B. Operation timed out

  C. Destination LPAR maximum memory setting is too low.

  D. HMC RMC daemons are not communicating properly to the source

  E. Source LPAR minimum memory setting is too high.

  F. Source LPAR maximum memory setting is too low.

  Correct Answer: C