HP HP Certifications HPE0-V14 Questions & Answers

• Question 211:

  Which protocol can be used to access a shared directory on a network-attached storage device?

  A. SNMP

  B. B.SMB

  C. FCP

  D. BGP

  Correct Answer: B

  They typically provide access to files using network file sharing protocols such as NFS, SMB, or AFP. Reference: https://en.wikipedia.org/wiki/Network-attached_storage

• Question 212:

  A customer is experiencing read cache hit ratios well below 80 percent on an HPE Nimble HF40 array Data is constantly being ejected from the Nimble array's First In First Out cache What should you recommend?

  A. Upgrade the SSD bundle to add more capacity.

  B. Enable InfoSlght's Al-based cache optimization setting

  C. Turn off deduplication on affected volumes

  D. Turn on deduplication on affected volumes.

  Correct Answer: C

• Question 213:

  A customer acquires an HPE 3PAR Storeserv 8200 Solution for a data center environment with the following configuration:

  2 Controllers Nodes Physical Service Processor 2-tier configuration using 16 SSD and 12 NL HDD 2 SN3000 San Switch each with 24 FC ports After installation and configuration, the storage is put in production. When tiering with the Adaptive Optimization SW is being performed, the customer encountered performance differential issue.

  What could be the cause of this issue?

  A. Disk enclosure are insufficient.

  B. File Controllers is missing.

  C. All-inclusive Multi-system software is missing.

  D. Solid State Drives and Nearline Drives are mixed.

  Correct Answer: D

  Reference: https://d8tadude.com/2015/03/10/3par-adaptive-optimization-design/

• Question 214:

  A customer ordered a pair of HPE SN3000B 16 Gb Fibre Channel Switches to provide Fibre Channel connectivity between VMware ESXi hosts and HPE 3PAR StoreServ 8200. Which adapter i s required to support Fibre Channel connectivity from the VMware ESXi hosts to the new switches?

  A. HBA

  B. SAS

  C. CNA

  D. NIC

  Correct Answer: A

• Question 215:

  Refer to the exhibit.

  

  An administrator connected a hypervisor to interface Ten-GigabitEthernet1/0/1 in a switch. The administrator created virtual machines in VLAN 10 and 20 on the hypervisor. VLAN 10 is configured to be tagged, and VLAN 20 is configured to

  be untagged on the hypervisor.

  The administrator found that all the virtual machines in VLAN 20 can communicate with each other, but not with any virtual machines on VLAN 20 external to the hypervisor.

  Given the output in the exhibit, customer needs a new environment to support an ERP system. The sizing information you received shows the following

  A. Permit VLAN 1 on the interface.

  B. Configure the PVID of the interface to be VLAN 20.

  C. Configure the interface as an access port.

  D. Configure the interface as an IRF port.check

  Correct Answer: B

• Question 216:

  Refer to the exhibit.

  

  You are validating a Nimble HF40 configuration created in OCA, and you receive an error when you run a CLIC check. Which Nimble component needs to be added to the configuration to complete the solution?

  A. HPE Nimble Storage HF40/60 Adaptive ES3 21TB HDD 1.44 TB Cache CTO Expansion Shelf

  B. HPE Nimble Storage HF40 Adaptive Array R2 2.88 TB FIO Cache Bundle

  C. HPE Nimble Storage Embedded 10GBASE-T 2-port FIO Adapter

  D. HPE Nimble Storage C19 to C20 250V 16 Amp 1.8m PDU Base Array FIO Power Cord

  Correct Answer: A

• Question 217:

  An HPE customer wants to perform is simplified update of firmware and drivers among their 100 HPE Gen9 and Gen10 racked servers.

  Which HPE software tool should the customer use to minimize the time required to perform this activity.

  A. HPE Smart Update Manager

  B. HPE OneView Standard

  C. HPE ProLiant Support Pack

  D. HPE iLO Amplifier Pack

  Correct Answer: A

  Reference: https://www.hpe.com/us/en/servers/smart-update.html

• Question 218:

  HPE support asks you to provide the Active Health System log from HPE StoreEasy 1660 Storage to expedite a troubleshooting process.

  Which procedures will generate the AHS log for HPE Support? (Choose two.)

  A. Download the AHS log from Server Manager dashboard

  B. Download the AHS log from Federation dashboard in StoreEasy Management Console

  C. Log in to the StoreEasy system with SSH and use the hpessacli command

  D. Boot to Intelligent Provisioning and download the AHS log from maintenance section

  E. Configure Remote Support on the iLO to send the log to HPE

  Correct Answer: DE

• Question 219:

  A customer is moving a server from a co-location facility back into their existing data center to comply with new internal policies on data management

  Due to budget constraints, the customer cannot purchase any additional switches and will need to use an existing end-of-row design with HPE FlexFabric switches While the server will be installed six racks away from the switches, the total cable run with cable management Is expected to be 35 m.

  Which component should be selected when designing the 10 Gbps connectivity option for the server?

  A. QSFP28 Active Optical Cable

  B. SFP+ 10G LC SR Transceiver

  C. SFP+ Active Optical Cable

  D. SFP+ Direct Attach Copper Cable

  E. QSFP+ Active Optical Cable

  Correct Answer: A

• Question 220:

  When should you choose to populate a server with LRDlMMs?

  A. when error correction is the most important factor

  B. when price is the most important factor

  C. when memory capacity is the most important factor

  D. when memory speed is the most important factor

  Correct Answer: D