HP HP Certifications HPE0-V14 Questions & Answers

• Question 261:

  A customer needs to integrate a new digital video surveillance solution into their existing environment and available network ports. The solution needs to include redundant hypervisor servers and a redundant SAN with a shared Fibre Channel attached storage array.

  You plan to propose the following configuration:

  2 HPE DL380 Gen10 servers with dual processors, 384 GB of memory, dual port 10 Gb NIC, and High Performance Fan Kit 1 HPE MSA 2050 Dual Controller Storage Array with 24x 1.8 TB 10 K SAS drives and 96x 7.2K NL drives 4 VMware vSphere Standard licenses 1 VMware vCenter Server Foundation licenses 5 year 24x7x4 support for all equipment

  What must be added to the configuration to provide a complete solution? (Choose two.)

  A. 2 HPE 10/25 Gb 2-port 622FLR-SFP28 CNA

  B. 2 HPE FlexFabric 5710 switches

  C. 2 Aruba 8320 switches

  D. 2 HPE SN3000B switches

  E. 2 HPE StoreFabric SN1200E 16 Gb Dual Port FC HBAs

  Correct Answer: DE

• Question 262:

  A customer needs a server memory subsystem that meets the following requirements:

  1.

  approaches the speed of traditional DRAM

  2.

  ensures high capacity, high performance, and ongoing data safety in case of a power failure

  Which HPE memory feature meets the customer needs?

  A. Load Reduced DIMMs

  B. Memory Mirroring

  C. Fast Fault Tolerance Memory

  D. Persistent Memory

  Correct Answer: D

  Reference: https://www.hpe.com/emea_europe/en/servers/persistent-memory.html

• Question 263:

  A customer needs to deploy an application on a newly-installed HPE ProLiant server, but they report that the server is not online. They call you for remote support. The IP address on the production network cannot be reached. You are evaluating the probable root causes of this issue.

  According to the troubleshooting methodology, what are next two steps? (Select two)

  A. Remote console into the ToR switch to check the server's port configuration.

  B. Log in to iLO to see if the server hardware and NIC are online and configured correctly.

  C. Use OneView to see f the server firmware is up-to-date

  D. Run insight Diagnostics on the Server

  E. Use Microsoft Remote Desktop or VNC to check the server's NIC and IP address configuration

  Correct Answer: BD

• Question 264:

  Read the question, and then refer to the exhibit.

  display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: Administratively DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: TenGigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK_SFP_PLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10, 20 VLAN permitted: 10, 20 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 18 seconds Last clearing of counters: Never Peak input rate: 78 bytes/sec, at 2011-03-31 04:55:57 Peak output rate: 15 bytes/sec, at 2011-03-30 23:00:57 Last 300 second input: 0 packets/sec 67 bytes/sec -% Last 300 second output: 0 packets/sec 14 bytes/sec -% Input (total): 62670 packets, 8565340 bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input (normal): 62670 packets, -bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, -overruns, 0 aborts ?ignored, -parity errors Output (total): 3707 packets, 1294835 bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output (normal): 3707 packets, -bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output: 0 output errors, -underruns, -buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, -no carrier

  A customer added a new switch to their network. They connected it using interface Ten-GigabitEthernet 1/0/1. They are using VLAN 10 and 20 for the devices in their network.

  The new switch was fully operational. Then, the customer experienced a power failure later that day and could not reach any device on the new switch after the power returned.

  From the output in the exhibit, would could be the issue?

  A. The interface loopback is not set.

  B. The interface link-speed and duplex are unknown.

  C. The interface is administratively down.

  D. The interface is configured for a PVID of VLAN 1.

  Correct Answer: C

  "display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: Administratively DOWN Line protocol state: DOWN IP"

• Question 265:

  Which HPE solution brings together CPU, Memory, and Disk with an unpredictable workload into a single management infrastructure?

  A. dHCI

  B. SimpliVity

  C. Nimble

  D. Primera

  Correct Answer: B

  Reference: https://community.hpe.com/t5/Around-the-Storage-Block/Accelerating-hyperconvergence-with-end-to-end-25GbE-storage/ba-p/7001560

• Question 266:

  HOTSPOT

  A solution integrator is installing new equipment to the rack.

  Click the recommended location for HPE R/T3000 Extended Runtime Module.

  Hot Area:

  

  Correct Answer:

  

  Answer is below rack 1 to 2 U UPS

• Question 267:

  HOTSPOT

  You need to review a warning on a Nimble storage array.

  Click on the menu option that displays this information.

  Hot Area:

  

  Correct Answer:

  

  Reference: https://infosight.hpe.com/InfoSight/media/cms/active/public/pubs_GUI_Administration_Guide_NOS_50x.whz/axc1501525262696.html

• Question 268:

  HOTSPOT You are configuring an MSA 2052 for one of your customers in OCA. Click on either one of the two places on the Bill of Materials screen that will enable you to verify the configuration and get details on any errors

  Hot Area:

  

  Correct Answer:

  

• Question 269:

  HOTSPOT

  A solution Integrator is installing new equipment to the rack.

  Click the recommended location area for R3000 Gen5 UPS.

  Hot Area:

  

  Correct Answer:

  

• Question 270:

  DRAG DROP

  Match each customer data center architecture to its network topology.

  Select and Place:

  

  Correct Answer: