HP HP Certifications HPE2-T37 Questions & Answers

• Question 11:

  Which HPE components can be managed using HPE Composer? (Select two.)

  A. HPE Superdome Flex 280

  B. HPE Synergy Virtual Connect SE 32Gb FC Module

  C. HPE Synergy 480 Compute Modules

  D. HPE B-series SN6600B Fibre Channel Switch

  E. HPE MSA 2062 Storage Array

  Correct Answer: BD

• Question 12:

  Refer to the exhibit.

  

  Your customer wants to define a Logical Interconnect Group (UG) and set the redundancy of the master modules to highly available, but this option is not available. What is a possible reason?

  A. There are not sufficient frames for highly available setup.

  B. Some master modules only support a redundant setup.

  C. Firmware on the master modules is too low to support highly available setup.

  D. A dedicated license must be added to HPE OneView to enable this feature.

  Correct Answer: B

• Question 13:

  Refer to the exhibit.

  

  Your customer created multiple networks in HPE OneView, but only Eth-1 is available to be used within a server profile. What is a likely cause of this situation?

  A. The other networks are not configured with the required Smart Link parameter.

  B. The other networks are not added to the Logical Interconnect Group configuration.

  C. The other networks have Private Network' selected, which hides them from Compute Modules.

  D. The other networks are configured with a purpose other than General or Management.

  Correct Answer: B

• Question 14:

  Which types of support dump can be created using HPE OneView? (Select two.)

  A. Enclosure group support dump

  B. Appliance support dump

  C. Firmware deployment support dump

  D. Logical enclosure support dump

  E. Maintenance console support dump

  Correct Answer: BD

• Question 15:

  You are deploying HPE OneView to manage a customer's HPE ProLiant servers

  Is this statement about appliance availability true?

  A. HA features for HPE OneView are enabled only if the appliance is deployed on an HPE SimpliVity cluster

  B. HPE OneView has a built-in HA feature that can be activated with an additional license

  C. HPE OneView availability relies on HA features provoed by the hypervisor

  D. During hpe oneView deployment customer may select configure proprietary HA mode.

  Correct Answer: C

• Question 16:

  A customer wants to estimate the cost of the licenses required to manage HP Synergy and some external components.

  When component includes an HPE OneView license for management?

  A. Compute Module

  B. Storage Array

  C. Master Module

  D. Logical Enclosure

  Correct Answer: A

• Question 17:

  Which statement about managing an HPE BiaoeSystem sever is true?

  A. A muiti-enclosure Vrtuai Connect domain can be imported to HPE OneView without disrupting servers

  B. An HPE server blade can be removed trom HPE OneView by deleting the server from the Server Hardware section

  C. An HPE server blade cannot be deleted from HPE OneView It must be physically removed from the enclosure

  D. Both c3000 and C7000 HPE BladeSystems enclosures can be imported to HPE Oneview for monitoring

  Correct Answer: B

• Question 18:

  You want to put two FlexNlCs into a single Link Aggregation Group within a server profile. What Is a prerequisite for this setup?

  A. The sFlow option must be enabled and configured.

  B. Both FlexNlCs must be connected to the same network.

  C. The Compute Module profile must have exactly two connections defined.

  D. An upgrade license must be purchased and deployed.

  Correct Answer: B

• Question 19:

  What is required to add a remote frame to the primary management ring?

  A. UUD of the remote HPE Composer

  B. Serial number of one of the remote frames

  C. Remote frame Link Module IPv6 address

  D. Request code from the primary HPE Composer

  Correct Answer: D

• Question 20:

  Which connection type can be defined within a server profile for an MPE ProLiant DL server?

  A. iSCSI

  B. RoCE

  C. FC

  D. Ethernet

  Correct Answer: C