Juniper Juniper Certifications JN0-361 Questions & Answers

• Question 41:

  Which two statements are true about NSR? (Choose two.)

  A. NSR requires graceful restart to function properly

  B. NSR requires redundant REs.

  C. NSR requires only one RE.

  D. NSR requires GRES to function properly.

  Correct Answer: BD

• Question 42:

  Click the Exhibit.

  

  You have just configured IS-IS, but the adjacency is not coming up. Referring to the exhibit, what is the cause?

  A. Only one side is configured using the point-to-point parameter.

  B. One router is configured for Level 2 only.

  C. The routers must be in different areas.

  D. The family iso parameters is missing on the interfaces.

  Correct Answer: A

• Question 43:

  Click the Exhibit.

  

  Referring to the exhibit, which two statements are true? (Choose two.)

  A. The LSP is protected with link protection.

  B. The last node in the path will not pop the MPLS label.

  C. The last node in the path will pop the MPLS label.

  D. The LSP is protected with fast reroute.

  Correct Answer: AC

• Question 44:

  Click the Exhibit.

  

  Your network consists of subnets shown in the exhibit. You are asked to create an aggregate route for Router 1. What is the appropriate prefix for the aggregate route in this scenario?

  A. 172.42.32.0/20

  B. 172.42.32.0/22

  C. 172.42.32.0/19

  D. 172.42.32.0/21

  Correct Answer: C

• Question 45:

  Because of recent network failures, additional circuits have been purchased. In addition, Fast reroute has been configured on critical MPLS LSPs. When the next failure occurs, which two time intervals will affect fast reroute? (Choose two.)

  A. The amount of time required to reroute the traffic onto the detour

  B. The amount of time to detect a link or node failure

  C. The amount of time required to recalculate the best detour

  D. The amount of time it takes to ping the gateway on the detour link

  Correct Answer: AB

• Question 46:

  What is the OSPFv3 router ID?

  A. 0.0.0.0

  B. 192.168.1.1

  C. 2001::1:2

  D. 2001::192.168.1.1

  Correct Answer: B

• Question 47:

  Click the Exhibit.

  

  Referring to the configuration in the exhibit, which statement is true?

  A. The next-hop 172.16.1.2 must be directly connected to the router for route 192.168.5.0/24 to be active.

  B. The next-hop 172.16.1.2 must be part of an active route in route table inet.0 for route 192.168.5.0/24 to be active.

  C. The next-hop 172.16.1.2 must respond to ping commands for the route 192.168.5.0/24 to be active.

  D. The next-hop 172.16.1.2 must be active in route table inet.3 for the route 192.168.5.0/24 to be active.

  Correct Answer: B

• Question 48:

  Click the exhibit.

  

  You have configured OSPF between two routers. The OSPF adjacency will not form. Referring to the exhibit, what is the problem?

  A. Router is not receiving hellos on the configured interface.

  B. The OSPF version does not match on the configured interfaces.

  C. The router is not sending hellos on the configured interface.

  D. The area does not match on the configured interfaces.

  Correct Answer: D

• Question 49:

  You are asked to configure and apply a new routing policy to influence routing advertisements received from a specific EBGP peer. In this scenario, which statement is true?

  A. The new policy should be applied as an export policy for the specific EBGP peer.

  B. The new policy should be applied as an import policy for the specific EBGP peer.

  C. The new policy should be applied as an export for the EBGP group in which the peer is defined.

  D. The new policy should be applied as an import policy for the EBGP group in which the peer is defined.

  Correct Answer: B

• Question 50:

  You are configuring a default static route using the default preference value. You want to ensure that any static route that you configure in the future will be less preferred than the OSPF routes that are configured on the network. Which command will accomplish this task?

  A. set protocols ospf preference 6

  B. set routing-options static route preference 9

  C. set routing-options static defaults preference 20

  D. set routing-options static defaults passive

  Correct Answer: C