1. Home
  2. Cisco
  3. 200-301

Implementing and Administering Cisco Solutions (CCNA) (Include Newest Simulation Labs)

Exam Details

  • Exam Code
    :200-301
  • Exam Name
    :Implementing and Administering Cisco Solutions (CCNA) (Include Newest Simulation Labs)
  • Certification
    :CCNA
  • Vendor
    :Cisco
  • Total Questions
    :1606 Q&As
  • Last Updated
    :Apr 14, 2025

Cisco CCNA 200-301 Questions & Answers

  • Question 531:

    Refer to the exhibit. Which next-hop IP address does Routed use for packets destined to host 10 10.13.158?

    A. 10.10.10.5

    B. 10.10.11.2

    C. 10.10.12.2

    D. 10.10.10.9

  • Question 532:

    Refer to the exhibit. The DHCP server and clients are connected to the same switch. What is the next step to complete the DHCP configuration to allow clients on VLAN 1 to receive addresses from the DHCP server?

    A. Configure the ip dhcp snooping trust command on the interlace that is connected to the DHCP client.

    B. Configure the ip dhcp relay information option command on the interface that is connected to the DHCP client.

    C. Configure the ip dhcp snooping trust command on the interface that is connected to the DHCP server.

    D. Configure the Ip dhcp relay information option command on the interface that is connected to the DHCP server.

  • Question 533:

    Refer to the exhibit.

    Site A was recently connected to site B over a new single-mode fiber path. Users at site A report Intermittent connectivity Issues with applications hosted at site B. What is the reason for the problem?

    A. Heavy usage is causing high latency.

    B. An incorrect type of transceiver has been inserted into a device on the link.

    C. physical network errors are being transmitted between the two sites.

    D. The wrong cable type was used to make the connection.

  • Question 534:

    Refer to the exhibit. Router R1 currently is configured to use R3 as the primary route to the Internet, and the route uses the default administrative distance settings. A network engineer must configure R1 so that it uses R2 as a backup, but only if R3 goes down. Which command must the engineer configure on R1 so that it correctly uses R2 as a backup route, without changing the administrative distance configuration on the link to R3?

    A. ip route 0.0.0.0 0.0.0.0 g0/1 1

    B. ip route 0.0.0.0 0.0.0.0 209.165.201.5 10

    C. ip route 0.0.0.0 0.0.0.0 209.165.200.226 1

    D. ip route 0,0.0.0 0.0.0.0 g0/1 6

  • Question 535:

    Refer to the exhibit. An engineer is asked to insert the new VLAN into the existing trunk without modifying anything previously configured Which command accomplishes this task?

    A. switchport trunk allowed vlan 100-104

    B. switchport trunk allowed vlan add 104

    C. switchport trunk allowed vlan all

    D. switchport trunk allowed vlan 104

  • Question 536:

    Refer to the exhibit.

    What is a reason for poor performance on the network interface?

    A. The interface is receiving excessive broadcast traffic.

    B. The cable connection between the two devices is faulty.

    C. The interface is operating at a different speed than the connected device.

    D. The bandwidth setting of the interface is misconfigured

  • Question 537:

    Refer to the exhibit. Routers R1 and R3 have the default configuration The router R2 priority is set to 99 Which commands on R3 configure it as the DR in the 10.0 4.0/24 network?

    A. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 100

    B. R3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 100

    C. R3(config)#interface Gig0/0 R3(config-if)i=ip ospf priority 1

    D. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 0

  • Question 538:

    Refer to the exhibit. Which plan must be Implemented to ensure optimal QoS marking practices on this network?

    A. As traffic traverses MLS1 remark the traffic, but trust all markings at the access layer.

    B. Trust the IP phone markings on SW1 and mark traffic entering SW2 at SW2.

    C. Remark traffic as it traverses R1 and trust all markings at the access layer.

    D. As traffic enters from the access layer on SW1 and SW2. trust all traffic markings.

  • Question 539:

    Refer to the exhibit. The link between PC1 and the switch is up. but it is performing poorly. Which interface condition is causing the performance problem?

    A. There is a duplex mismatch on the interface

    B. There is an issue with the fiber on the switch interface.

    C. There is a speed mismatch on the interface.

    D. There is an interface type mismatch

  • Question 540:

    Refer to the exhibit.

    An engineer is configuring the HO router. Which IPv6 address configuration must be applied to the router fa0'1 interface for the router to assign a unique 64-brt IPv6 address to Itself?

    A. ipv6 address 2001:DB8:0:1:C601:42FF:FE0F:7/64

    B. ipv6 address 2001:DB8:0:1:C601:42FE:800F:7/64

    C. ipv6 address 2001 :DB8:0:1:FFFF:C601:420F:7/64

    D. ipv6 address 2001 :DB8:0:1:FE80:C601:420F:7/64

Related Exams:

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Cisco exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 200-301 exam preparations and Cisco certification application, do not hesitate to visit our Vcedump.com to find your solutions here.