Cisco CCNP Enterprise 300-430 Questions & Answers

• Question 81:

  An engineer is managing a wireless network for a shopping center. The network includes a Cisco WLC, a Cisco MSE, and a Cisco Prime Infrastructure. What is required to use Cisco CMX Location Analytics?

  A. Enable tracking parameters in Cisco MSE.

  B. Enable Context Aware and CMX Browser Engage.

  C. Install Cisco Prime Infrastructure with floor maps.

  D. Set history parameters in Cisco MSE.

  Correct Answer: C

  https://www.cisco.com/c/en/us/td/docs/wireless/mse/10-6/cmx_config/b_cg_cmx106/getting_started_with_cisco_cmx.html

• Question 82:

  An engineer is responsible for a wireless network for an enterprise. The enterprise has distributed offices around the globe, and all APs are configured in FlexConnect mode. The network must be configured to support 802.11r and CCKM. What needs to be implemented to accomplish this goal?

  A. Enable VLAN-based central switching.

  B. Enable FlexConnect local authentication.

  C. Enable FlexConnect local switching.

  D. Create FlexConnect groups.

  Correct Answer: D

• Question 83:

  Refer to the exhibit.

  

  An engineer needs to configure location services in an office. The requirement is to use FastLocate and achieve higher locations refresh rates. Which location-based technique should be implemented?

  A. probe-based

  B. location patterning

  C. data packet-based

  D. angulation

  Correct Answer: C

• Question 84:

  What is the maximum time range that can be viewed on the Cisco DNA Center issues and alarms page?

  A. 3 hours

  B. 24 hours

  C. 3 days

  D. 7 days

  Correct Answer: D

• Question 85:

  A customer requires wireless traffic from the branch to be routed through the firewall at corporate headquarters. A RADIUS server is in each branch location. Which Cisco FlexConnect configuration must be used?

  A. central authentication and local switching

  B. central authentication and central switching

  C. local authentication and local switching

  D. local authentication and central switching

  Correct Answer: D

• Question 86:

  Refer to the exhibit.

  

  An engineer must restrict some subnets to have access to the WLC. When the CPU ACL function is enabled, no ACLs in the drop-down list are seen. What is the cause of the problem?

  A. The ACL does not have a rule that is specified to the Management interface.

  B. No ACLs have been created under the Access Control List tab.

  C. When the ACL is created, it must be specified that it is a CPU ACL.

  D. This configuration must be performed through the CLI and not though the web GUI.

  Correct Answer: B

• Question 87:

  Refer to the exhibit.

  

  Which area indicates the greatest impact on the wireless network when viewing the Cisco CleanAir Zone of Impact map of interferers?

  A. A

  B. B

  C. C

  D. D

  Correct Answer: D

• Question 88:

  A wireless network engineer must present a list of all rogue APs with a high severity score to senior management. Which report must be created in Cisco Prime Infrastructure to provide this information?

  A. Rogue AP Count Summary

  B. New Rogue APs

  C. Rogue AP Events

  D. Rogue APs

  Correct Answer: D

• Question 89:

  An engineer must run a Client Traffic Stream Metrics report in Cisco Prime Infrastructure. Which task must be run before the report?

  A. scheduled report

  B. radio performance

  C. client status

  D. software

  Correct Answer: B

  Reference: https://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2- 0/user/guide/prime_infra_ug/reps.html

• Question 90:

  An engineer needs to provision certificates on a Cisco Catalyst 9800 Series Wireless Controller. The customer uses a third-party CA server. Which protocol must be used between the controller and CA server to request and install certificates?

  A. SCEP

  B. TLS

  C. LDAP

  D. SSL

  Correct Answer: A

  Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/config-guide/trustpoints/b-configuring-trustpoints-on-cisco-catalyst-9800-series-controllers/c-workflow-to-configure-a-trustpoint-for-a-third-party-certificate-on-catalyst9800.html