F5 F5 Certifications 301A Questions & Answers

• Question 101:

  Consider the monitor configuration displayed below.

  

  What is the status of a pool member that responds with ''200 OK''?

  A. available

  B. down

  C. disabled

  D. unknown

  Correct Answer: B

• Question 102:

  An LTM Specialist is removing some of the load off an existing cluster by adding a adding a third BIG- IP

  device to the device group. The new device can deliver twice the performance of the other two devices.

  The LTM Specialist needs to make sure that the BIG-IP device with the highest available capacity is

  always selected to take over a traffic group in the event of a failover.

  Which failover method is most appropriate?

  A. Ordered List

  B. Load Aware

  C. HA Group

  D. HA Capacity

  Correct Answer: A

• Question 103:

  A virtual server with SNAT automap enabled selects pool member 10.20.0.10.443 for the server-side flow. The client side flow source IP is 192.168.0.10 .

  

  Which source IP should be expected in the server-side connection?

  A. 10.20.0.1

  B. 10.50.0.2

  C. 10.20.0.2

  D. 192.168.0.10

  Correct Answer: C

• Question 104:

  Refer to the following iRule:

  

  What is a complete list of profiles that must be applied to the virtual server for this iRule?

  A. Fast L4, HTTP

  B. TCP, HTTP

  C. TCP, HTTP, Client SSL

  D. Fast L4 , HTTP, Stream

  Correct Answer: B

• Question 105:

  An LTM Specialist has noticed in the audit log that there are numerous attempts to log into the Admin

  account. Theses attempts are sourced from a suspicious IP address range to the Configuration Utility of

  the LTM device.

  How should the LTM Specialist block these attempts?

  A. add the permitted source IP addresses to the httpd allow list via tmsh

  B. add the suspicious source IP addresses to the httpd deny list via tmsh

  C. add the suspicious source IP addresses to the httpd deny list via Configuration Utility

  D. add the permitted source IP addresses to the allow list via Configuration Utility

  Correct Answer: A

• Question 106:

  A Client makes the request displayed below to the application server. Which virtual server type should an LTM Specialist use to load balance based on the URL? .

  A. Forwarding (Layer 2)

  B. Stateless

  C. Standard

  D. Performance (Layer 4)

  Correct Answer: C

• Question 107:

  An LTM Specialist configures a new virtual server with a single pool member. The LTM Specialist has NOT

  defined a health monitor for the pool, pool member or node.

  What is the status of the virtual server?

  A. Available (Enabled)

  B. Offline (Disabled)

  C. Unavailable (Enabled)

  D. Unknown (Enabled)

  Correct Answer: D

• Question 108:

  An LTM Specialist has recently taken over administration or an LTM device that has experienced resource availability issues. The LTM device will need to be solely used for load balancing and SSL offload. Previously, the LTM device was also used to provide statistical analysis of application traffic. However, that functionality has been moved to a third party solution. Based on the output below, which configuration change should be made to ensure the LTM module receives the most amount of resources?

  

  A. Provision AVR to Minimum. Provision LTM at Maximum

  B. Provision AVR to none. Provision LTM to Dedicated

  C. Provision AVR to Minimum, Provision LTM to Dedicated

  D. Provision LTM to Dedicated, Provision AVR to Dedicated

  Correct Answer: B

• Question 109:

  An LTM Specialist needs to provide statistics regarding the round-trip time between the clients and the

  servers.

  Which metric should be part of the analytics profile to provide that information?

  A. Page Load Time

  B. User Sessions

  C. Max TPS and Throughout

  D. Response Codes

  Correct Answer: A

• Question 110:

  In an iApp, which configuration protects against accidental changes to an application Services configuration?

  A. Components

  B. Strict Updates

  C. Name

  D. Template

  Correct Answer: B