Cisco CCNP Enterprise 350-401 Questions & Answers

• Question 31:

  What is a characteristic of vManage?

  A. It leverages the overlay management protocol to interface with WAN Edge devices.

  B. It supports protocols such as OSPF to integrate with legacy network devices.

  C. It requires a public IP address to allow WAN Edge devices to discover fabric components.

  D. It uses NETCONF to configure vSmart devices to build the overlay network data plane.

  Correct Answer: D

• Question 32:

  Refer to the exhibit.

  

  What does the response "204 No Content" mean for the REST API request?

  A. Interface loopback 100 is removed from the configuration.

  B. Interface loopback 100 is not removed from the configuration.

  C. Interface loopback 100 is not found in the configuration.

  D. The DELETE method is not supported.

  Correct Answer: C

• Question 33:

  What gives priority on an egress interface, for database traffic that connected on an ingress interface, without changing the CoS value?

  A. QoS group

  B. policy map

  C. CoS map

  D. class map

  Correct Answer: B

• Question 34:

  Which NTP concept is used to measure the distance from a device to its authoritative time source?

  A. stratum

  B. NTP peer

  C. GPS

  D. atomic clock

  Correct Answer: A

  Reference: https://www.cisco.com/c/dam/en/us/td/docs/ios-xml/ios/bsm/configuration/xe-3se/3650/bsm-xe-3se-3650-book.html#:~:text=NTP%20uses%20the%20concept%20of,from%20an%20authoritative%20time%20source

• Question 35:

  Refer to the exhibit.

  

  What is the purpose of the configuration?

  A. The router will function in NTP in client mode.

  B. The router will use 172.16.1.1 as the source for NTP packets.

  C. The router is allowed to receive NTP broadcast packets.

  D. The router will function as an authoritative NTP server.

  Correct Answer: D

• Question 36:

  When are multicast RPs required?

  A. RPs are required only when using protocol independent multicast dense mode.

  B. By default, the RP is needed penodically to maintain sessions with sources and receivers.

  C. RPs are required for protocol Independent multicast sparse mode and dense mode.

  D. By default, the RP Is needed only start new sessions with sources and receivers.

  Correct Answer: D

• Question 37:

  A network engineer must configure the VTY lines on a router to achieve these results:

  1.

  Remote access should be permitted only for secure protocols.

  2.

  Only a password should be required for device authentication.

  3.

  All idle EXEC sessions must be terminated in 60 minutes.

  Which configuration should be applied?

  A. line vty 0 15 password Cisco123 transport input ssh exec-timeout 60

  B. line vty 0 15 login password Cisco123 transport input ssh exec-timeout 60

  C. line vty 0 15 password Cisco123 transport input telnet ssh exec-timeout 60

  D. line vty 0 15 password Cisco123 transport input all session-timeout 60

  Correct Answer: B

• Question 38:

  Refer to the exhibit.

  

  What is the result of the NTP configuration?

  A. The router will use the address of loppback 0 to communicate with the NTP server.

  B. The router will advertise but not listen to NTP broadcast packets.

  C. The router will be used as an NTP authoritative server only if it synchronized with an outside source.

  D. The router will be used as an NTP authoritative server, even if it is not synchronized with an outside source.

  Correct Answer: D

• Question 39:

  A client requests a wireless solution for remote branch offices to eliminate the need for a local controller at each branch. The branch users require local termination in a specifc VLAN for local internet breakout. Which solution must be deployed?

  A. central switched

  B. FlexConnect local switching

  C. auto-anchor mobility

  D. asymmetric tunneling

  Correct Answer: B

  Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-5/config-guide/b_cg85/flexconnect.html

• Question 40:

  Which device, in a LISP router architecture, receives LISP map requests and determines which ETR should handle the map request?

  A. proxy ETR

  B. routing locator

  C. map resolver

  D. map server

  Correct Answer: C

  LISP Map Resolver Like an MS, a LISP MR connects to the ALT. The function of the LISP MR is to accept encapsulated Map-Request messages from ingress tunnel routers (ITRs), decapsulate those messages, and then forward the messages to the MS responsible for the egress tunnel routers (ETRs) that are authoritative for the requested EIDs.