Avaya ACIS 3605 Questions & Answers

• Question 21:

  Routed Split Multilinking Trunking (RSMLT) is a way to ensure that traffic can be routed off the VLAN by adding router redundancy. RSMLT is configured on which Ethernet Routing Switch (ERS) configuration component?

  A. an OSPF router

  B. a core switch port

  C. a VLAN

  D. an SMLT

  Correct Answer: A

• Question 22:

  A technician is configuring the core of a Converged Campus network, and is adding a backup-master configuration to an existing Virtual Router Redundancy

  Protocol (VRRP) configuration for a VLAN that extends to the edge switches.

  Which benefit is expected from the Addition of backup-master?

  A. reduced traffic on the IST

  B. reduced traffic on the uplink ports

  C. redundant default gateways for host devices

  D. faster switchover time

  Correct Answer: D

• Question 23:

  Click the exhibit button.

  

  SLPP has just been enabled on both core switches.

  Based on the network diagram and console output from the core 1 Ethernet Routing Switch (ERS) B600 shown in the exhibit, what is the configuration error on the

  edge switch?

  A. The edge switch spanning-trcc has not been configured.

  B. The edge switch access port rate limiting has not been configured.

  C. The edge MLT has not been configured correctly.

  D. The edge VUXNs has not been configured.

  Correct Answer: A

• Question 24:

  A technician is configuring password levels on the Ethernet Routing Switch (ERS) 8600, and wants the manager to be able to view and edit most device settings, but not be able to change security and password settings. Which login Level should be set for the manager?

  A. Layer 2 Read Write Access

  B. Layer3Read-WnteAccess

  C. Read Write All Access

  D. Read-Write Access

  Correct Answer: D

• Question 25:

  One of the switches in the Ethernet Routing Switch (ERS) stacks files and is replaced. The auto unit replacement (AUR) is enabled but the stack is not functioning

  properly.

  What is the problem?

  A. The switches in the stack are not identical

  B. the stack power was left on during the switch replacement.

  C. The switches in the stack are not running the same release of software

  D. The stack has two switches with Force Stack disabled.

  Correct Answer: B

• Question 26:

  A technician needs to reboot an Ethernet Routing Switch (ERS) 5000 Series switch with a default configuration. What needs to be done to keep the IP address and stack license?

  A. Boot partial-default

  B. Boot-default save-license

  C. Boot default-save

  D. Boot restore-license

  Correct Answer: A

• Question 27:

  A customer needs to install a new Ethernet Routing Switch (ERS) 2550T on the 172.16.5.0/24 network, but does not have a console cable available. Which statement is correct?

  A. The switch will first attempt to use BootP to acquire an IP address, and if that fails it will assign IP address 192.160.1.1/24 to the switch IP.

  B. The customer can set the switch to use the temporary address of 192.168.192.168 by pressing the User Interface button on the front of the ERS 2550T

  C. To communicate with an ERS 2550T the IP address must first be set though the console interface.

  D. The customer can connect to the network management Ethernet port which is pre-configured to use the 192 168 1 1/24 IP address

  Correct Answer: D

• Question 28:

  In a newly installed network the port LED on an Ethernet Routing Switch (ERS) 5500 is amber, not green. What does this mean?

  A. The port is set to operate at 10 Mbps.

  B. The port is set to operate at 100 Mbps.

  C. It indicates that there is a transmit fault.

  D. It indicates that the port is administratively disabled.

  Correct Answer: D

• Question 29:

  The Ethernet routing switch (ERS) 5000 switches are being upgraded and it appears that a license is not recognized on the switch. Which two statements are valid sources of information that will help resolve the license installation? (Choose two.)

  A. Check for an 'invalid license fife' log report

  B. Check the record of MSG address changes

  C. Use the show license command to get the license installation status

  D. Check to see if the MAC address is correct in the license file.

  E. Use the show license file command to get the license installation status.

  Correct Answer: CD

• Question 30:

  A technician has installed a license file on the Ethernet routing switch (ERS) 8800 and rebooted, but cannot configure the associated licensed features. it has been determined that license did not load properly at booyup time.

  Which two must be verified?

  A. The switch is at the current release.

  B. The license filename contains valid characters.

  C. The license file is stored in the flash directory

  D. The appropriate license level has been obtained.

  E. The license file has .dat extension.

  Correct Answer: BE