When troubleshooting a LAN connectivity issue, you notice a failed uplink from the Cisco UCS Fabric Interconnects to the upstream LAN switch. What two could be causing the issue? (Choose two )
A. Misconfigured VLAN on the failed uplink
B. Misconfigured QoS parameters on the failed uplink
C. A port channel mismatch between the Fabric Interconnects and the upstream LAN switch
D. A SFP Type mismatch between the Fabric Interconnects and the upstream LAN switch
E. A port speed configuration mismatch between the Fabric Interconnects and the upstream LAN switch
What are three possible causes of service profile association failure due to iSCSI configuration issue? (Choose three )
A. Wrong WWNN
B. iSCSI Target out of configured range of services
C. Inappropriate network configuration
D. Improperly assigned iSCSI Class of Service
E. Misconfigured iSCSI parameters
F. Misconfigured LUN. LUN masking
After performing a UCS firmware upgrade, which two UCS components will require updated drivers? (Choose two )
A. VIC Cards and Fiber Channel HBAs
B. Cisco Fabric Interconnects
C. Cisco UCS Manager
D. RAID Controllers
When troubleshooting, which option is the primary uses of the SCOPE command?
A. To access the log files on the log server
B. The SCOPE command is not helpful in this case
C. To access the log files on the virtual machines
D. To access the log files that reside in a component
Which statement is true regarding the UCS Manager GUI is showing "Overall Status Unassociated" in the General tab for a C-series server?
A. The server has a service profile assigned, but has connectivity issues with UCS Manager
B. The server is not properly connected
C. The server does not have a service profile assigned, but has been discovered by UCS Manager
D. The server has been properly connected, but has not been discovered by UCS Manager
The command show interface veth 705 is telling you that the bound interface is Ethernet 3/1/2
What is the location of the blade that has veth 705 associated to it?
A. Chassis 3, Slot 1
B. Chassis 3. Slot 2
C. There is not enough information
D. Chassis 1. Slot 2
What three options should be verified, when you are able to connect to Cisco UCS Manager, but unable to open a KVM session to a blade? (Choose three)
A. Verify TCP port 2068 is not blocked by an ACL or Firewall
B. Confirm the IP Address assigned to UCS Manager is the same as the KVM address
C. Verify the KVM IP Address is on the same ip subnet as the virtual machines
D. Confirm the KVM IP Address is added to the route table in Cisco UCS Manager
E. Confirm the IP Address assigned to the KVM is not a duplicate IP
F. Verify the KVM IP Address is on the same subnet as the Fabric Interconnect management address
When configuring UCS SAN Connectivity to a 3rd Party FibreChannel Storage Array that is connecting directly to the UCS Fabric Interconnects, which option is Cisco recommended'?
A. Connect the Storage Array to a RC Storage Port and Enable NPV Mode on the UCS Fabric Interconnects
B. Connect the Storage Array to an Appliance Port and Enable NPV Mode on the UCS Fabric Interconnects
C. Direct connectivity between UCS Fabric Interconnects and FibreChannel Storage Arrays is not supported
D. Connect the Storage Array to a FC Storage Port and Enable Switching Mode on the UCS Fabric Interconnects
E. Connect the Storage Array to an Appliance Port and Enable Switching Mode on the UCS Fabric Interconnects
You are in the process of upgrading your UCS M3 Server to a newer UCS M4 Server. You associate the Service Profile to the new UCS Server, but it fails to boot You suspect of a failed boot hard drive. You check your RAID1 Boot LUN in UCS Manager, but see no error messages
What could be causing the issue?
A. The newer Cisco UCS M4 Server is using flash drives, not hard drives
B. The newer Cisco UCS M4 Server is using disks of larger capacity than the previous UCS M3 Server
C. A misconfiguration on the Service Profile Local Boot Policy
D. A misconfiguration on the Service Profile Local Disk Policy
Which two ports on a pair of Cisco Fabric Interconnects must be properly cabled for the pair to form a cluster? (Choose two )
A. L1 > L1
B. L1 > L2
C. L2 > L2
D. L2 > L1
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Cisco exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 500-920 exam preparations and Cisco certification application, do not hesitate to visit our Vcedump.com to find your solutions here.