HP HP ExpertONE Certification HP2-T23 Questions & Answers

• Question 21:

  Which HP tool can you use to deploy firmware and software updates to a ProLiant server blade?

  A. Insight Diagnostics

  B. Software Update Manager

  C. System Management Homepage

  D. Service Pack for ProLiant

  Correct Answer: B

• Question 22:

  Which step must be performed after the system board is replaced on a ProLiant BL460c G8 server blade?

  A. Enable ASR.

  B. Re-enter the serial number.

  C. Clear the NVRAM.

  D. Reconfigure the array.

  Correct Answer: B

• Question 23:

  After you replace the system board in a ProLiantBL460c G8 server blade,the server cannot conned to an external shared storage through the SAS interface. Other similar servers in the same enclosure are in working condition. What should you check to verify that the physical hardware connectivity it connected?

  A. External storage power status

  B. ACU of the server blade for storage status

  C. Server bladeiLO tot hardware information detected by the management processor

  D. Server blade port mapping for theIOmodule connectivity to the interconnect module

  Correct Answer: D

• Question 24:

  A server has been shutting down sporadically for the past two months. Version Control Repository Manager (VCRM) is not installed or configured.

  Where can you locate the latest versions of firmware that are available for this server?

  A. PSP DVD

  B. HP website

  C. SmartStart

  D. server image file from two months ago

  Correct Answer: B

• Question 25:

  How do you boot into Intelligent Provisioning on a ProLiant Gen8 server?

  A. By pressing the F9 button during POST

  B. By pressing the F10 button during POST

  C. Through a Scripting Toolkit server configuration script

  D. Through the Array Configuration Utility (ACU) in offline mode

  Correct Answer: B

• Question 26:

  A support engineer is troubleshooting a ProLiant DL360p Gen8 server.A hard disk m a four drive RAID 5 set has failed.The engineer notices that on three of the drives, the LEO labeled D on the exhibit is on.What does the condition indicate?

  

  A. Hot swapping of the failed drive is not supported in this condition

  B. The LED indicates failure and predictive failure alerts. Two additional drives in the RAID set are at risk of failing and need to be replaced

  C. The drives should not be removed when this LED is illuminated

  D. The drive failure has corrupted three drives in the RAID set. The array must be rebuilt and data restored from backup

  Correct Answer: C

• Question 27:

  Which steps should you perform to save a Virtual Connect configuration?

  A. From CLI show all > cfg.txt

  B. Enclosure setting configuration scripts show, config save

  C. Enclosure setting configuration scripts inventory

  D. VCM Tools Backup/Restore Domain Configuration

  Correct Answer: D

• Question 28:

  Which RAID level allows the data to be striped across multiple RAIDs? (Select two.)

  A. RAID 0

  B. RAID 1

  C. RAID 5

  D. RAID 50

  E. RAID 60

  Correct Answer: AD

• Question 29:

  Which statements are correct about the HP Customer Self Repair (CSR) program? (Select two.)

  A. A travel and labor charge applies when customers decline to replace an optional CSR part.

  B. A travel and labor charge does not apply when customers decline to replace an optional CSR part.

  C. A travel and labor charge does not apply when customers decline to replace a mandatory CSR part.

  D. A travel and labor charge applies when customers decline to replace a mandatory CSR part.

  Correct Answer: AC

• Question 30:

  Which software tool should you use to deploy an operating system to a ProLiant BL460c Gen8 server blade?

  A. System Management Homepage

  B. Array Configuration Utility

  C. SmartStart

  D. Intelligent Provisioning

  Correct Answer: D