HP HP ExpertONE Certification HP2-T23 Questions & Answers

• Question 41:

  You ate installing a new HP BladeSystem c7000 enclosure. The customer wants to configure the iLO and interconnect IP addresses so that they are automatically maintained during a hardware swap How should you configure the enclosure?

  A. Use the Insight Display fixed IP feature.

  B. Configure the IP on each device and enable one enclosure IP mode.

  C. Use Insight Control Server Deployment to configure the enclosure.

  D. Use Enclosure-Bay IP Addressing.

  Correct Answer: D

• Question 42:

  What should be run in the Virtual Connect Support Utility (VCSU) before initiating a Virtual Connect firmware upgrade?

  A. Show all

  B. VC Support Dump

  C. Health Check

  D. Show Config

  Correct Answer: C

• Question 43:

  Which RAID level is known as Advance Data Guarding (ADG)?

  A. RAID 1

  B. RAID 5

  C. RAID 6

  D. RAID 10

  Correct Answer: C

• Question 44:

  An engineer is installing an HP R7000 UPS and an Extended Runtime Module (ERM) in an existing HP 10642 G2 rack. This rack contains 10 ProLiant DL380e Gen8 servers mounted from 1U upward.

  How should the engineer perform this installation?

  A. Mount the R7000 UPS at 10U in the 10642 G2 rack with the ERM on top of the R7000 UPS.

  B. Remove the lowest ProLiant DL380e Gen8 servers and mount the R7000 and the ERM at the lowest position in the rack. Mount the removed ProLiant DL380e Gen8 servers at a higher position in the 10642 G2 rack.

  C. Mount the R7000 at the highest position possible in the 10642 G2 rack with the ERM just below the UPS.

  D. Remove the two lowest mounted ProLiant DL380e Gen8 servers and mount the R7000 at the bottom of the 10642 G2 rack. Mount the two removed ProLiant DL380e Gen8 servers at the top of the 10642 G2 rack. Mount the ERM above the remaining original mounted ProLiant DL380e Gen8 servers.

  Correct Answer: B

• Question 45:

  An engineer replaced a tape drive that failed. What is the best method for testing this drive during business hours?

  A. Run online Insight Diagnostics and check the IE logs.

  B. Use L and TT to perform an assessment test.

  C. Use L and T T to perform a device self test.

  D. Run offline insight Diagnostics.

  Correct Answer: C

• Question 46:

  An administrator installed HP CS Platinum/Platinum Plus Power Supplies in an enclosure with ProLiant server blades.

  Which additional components does the administrator need in order to track power usage and automate server discovery in the enclosure?

  A. HP iPDU and HP Power Regulator

  B. HP Insight Control and RBSU

  C. HP iPDU and HP Remote Support

  D. HP iPDU and HP Insight Control

  Correct Answer: D

• Question 47:

  You are troubleshooting a problem with a ProLiant BL460c Gen8 server and need a report detailing the firmware and driver revisions on the server. Which report should you obtain?

  A. iLO Event Logs

  B. Array Diagnostics Report

  C. Integrated Management Log

  D. Active Health Logs

  Correct Answer: B

• Question 48:

  Where is the data written when power is lost on an HP Smart Array controller?

  A. Master boot record

  B. Flash backed write cache

  C. Network controller

  D. System memory

  Correct Answer: B

• Question 49:

  An engineer repaired a memory problem in a ProLiant BL460c Gen8 server blade running Windows 2008 R2. What should the engineer do to verify the repair? (Select two.)

  A. Observe the Insight Display at the front of the server after it boots.

  B. Check the Active Health System.

  C. Observe the server console for POST errors.

  D. Reboot the BL460c Gen8 server and run the offline Insight Diagnostics.

  E. Reseat the memory and inform the customer when the job is done.

  Correct Answer: AD

• Question 50:

  Which function of ProLiant Gen8 server blades constantly records configuration, performance, and operational data?

  A. Integrated Management Log

  B. Event Log

  C. Health Agent

  D. Active Health

  Correct Answer: D