IBM IBM Certified System Administrator - AIX V1 C9010-022 Questions & Answers

• Question 61:

  An administrator attempts to install the fileset tivoli.tsm.client, but it fails due to missing requisites.

  The administrator copies the required filesets into the install directory and tries the preview install again. It fails with the same results, as shown in the graphic below.

  What must the administrator do to successfully install the filesets?

  

  A. Remove the .toe file or run inutoc.

  B. Provide the correct version of xlsmp.rte.

  C. Make the permissions of all of the filesets group executable

  D. Make the permissions of the requisite filesets group readable

  Correct Answer: A

• Question 62:

  Which standard filesystem is temporarily used by the mksysb backup process?

  A. /mnt

  B. /tmp

  C. /usr/tmp

  D. /var/ras/tmp

  Correct Answer: D

• Question 63:

  A company has combined multiple Web servers into one AIX LPAR with a single physical network connection. How can AIX be configured with multiple IP addresses on the same physical connection?

  A. Add the additional IP addresses as aliases in DNS.

  B. Add the IP addresses to the primary hostname line in /etc/hosts.

  C. Add the additional IP addresses as aliases to the network connection.

  D. Assign the IP addresses to virtual Ethernet adapters and map them to the physical network connection.

  Correct Answer: C

• Question 64:

  When attempting to log into a system, the administrator receives the message "All network ports in use."

  How can this be resolved?

  A. Add the terminals tty0 through tty9 to the /etc/securetty file

  B. Use thenocommand to enable ipforwarding

  C. On the HMC,select the option "Reset Connection" for the server

  D. Use thechdevcommand to increase the number of pseudo-terminals

  Correct Answer: D

• Question 65:

  An administrator is tasked with enhancing the data availability and I/O load balancing for an AIX 7.1 system attached to IBM storage.

  Which action will satisfy the requirement?

  A. Set the correct host type on the storage array and match the failover settings on the AIX instance.

  B. Adjust the health check interval attribute for each hdisk presented from the storage array.

  C. Install the appropriate path control module to work in conjunctionwith the native MPIO driver.

  D. Remove the native MPIO driver and replace with the appropriate path control module.

  Correct Answer: B

• Question 66:

  After successfully mirroring rootvg using the mirrorvg command, why must the bosboot command be run against the introduced disk?

  A. To update the boot list held in NVRAM

  B. To record from which disk the system will boot

  C. To customize the bootrec of the newly mirrored drive

  D. To synchronize the boot record between the mirrored drives

  Correct Answer: C

• Question 67:

  What is the purpose of the certify operation against a local disk drive?

  A. Formats the drive

  B. Erases the drive

  C. Verifies sector integrity

  D. Establishes device quorum

  Correct Answer: B

• Question 68:

  When preparing to install a System WPAR using NIM, what action must occur before the planned WPAR can be successfully defined as a NIM client?

  A. Install AIX onto the global environment.

  B. Register the planned hostnamesto DNS.

  C. Define the global environment LPAR as a NIM client.

  D. Create an lpp_source with the WPAR-specific backup files.

  Correct Answer: C

• Question 69:

  When defining a new NIM client, an administrator is prompted to select the type of network.

  

  Why does a NIM Master prompt for this confirmation?

  A. The nimesis service is not active on the client.

  B. A NIM network for the hosting subnet has not yet been defined.

  C. There is not Network Install Routingobject to list the route to the adjacent subnet.

  D. The NIM Master's Primary Interface has not been initialized.

  Correct Answer: B

• Question 70:

  A VIO client will use NPIV to boot from the SAN and needs to be installed using NIM.

  Which two methods canbe used to gather the WWPN information? (Choose two.)

  A. Examine the NIM client properties.

  B. Boot the LPAR and runlscfg –vl fcsX

  C. Utilize the HMC command line tool, lssyscfg

  D. Log into the VIO servers and runlscfg –vl fcsX

  E. Check the LPAR properties from the HMC GUI

  Correct Answer: AE