HP HP Certifications HPE6-A72 Questions & Answers

• Question 31:

  You have completed a successful VSF stack between two switches.

  Without manually assigning a backup switch, what is the expected output when issuing a show vsf command?

  

  A. Option A

  B. Option B

  C. Option C

  D. Option D

  Correct Answer: D

• Question 32:

  Which two types of routes can be found in the IP routing table of an Aruba AOS-CX switch? (Choose two.)

  A. Local

  B. EIGRP

  C. BGP

  D. ISIS

  E. RIPng

  Correct Answer: AC

• Question 33:

  Refer to the exhibit.

  

  All four switches in the diagram have been configured with the region name "Aruba1".

  What two other MSTP configurations must match for switches within the same MST region? (Choose two.)

  A. MST region type

  B. MST Bridge ID

  C. MST version number

  D. MST revision number

  E. MST VLAN to instance mapping

  Correct Answer: DE

• Question 34:

  What are two mechanisms supported on AOS-CX 6300 switches used in Multi-active Detection to determine the status of the Primary member? (Choose two.)

  A. Management interface split detection

  B. Peer switch-based detection

  C. Loopback keepalives

  D. ARP-based

  E. BFD

  Correct Answer: AD

• Question 35:

  Which two statements accurately describe the features of NetEdit? (Choose two.)

  A. NetEdit can be used to configure and validate any third-party device that supports SSH and REST access.

  B. NetEdit includes trial licensing for up to 10 nodes.

  C. NetEdit can perform configuration and compliance validation.

  D. NetEdit supports viewing and editing multiple devices using a single deployment plan.

  E. NetEdit can run on a mobile device using Android or Apple IOS.

  Correct Answer: CD

• Question 36:

  Which statement is true regarding modern switching requirements?

  A. Most older legacy switches had high port bandwidth utilization and were future proof designed to meet today's power-over-Ethernet needs.

  B. Requirements for PoE are normally addressed using AC to DC power adapters. Concerns for port security for IoT devices are usually addressed using default wired encryption that all 802.3 Ethernet switches provide.

  C. While APs are common, most clients are still docked and only require traditional wired connections with only the occasional dedicated PoE switch to provide power for the low number of devices needed.

  D. Clients tend to prefer wireless connections, raising the need for PoE port access. There is also a growing amount of IoT devices that require security and port authentication options.

  Correct Answer: D

• Question 37:

  Which command can be used to find the serial number of an Aruba OS-CX switch?

  A. The command inventory

  B. The command version

  C. The command show running-configuration

  D. The command show system

  Correct Answer: D

• Question 38:

  Refer to the exhibit

  

  What is true regarding VLAN 50 according to the diagram above?

  A. VLAN 50 is part of a switched virtual interface (SVI) that was never routed causing it to be down.

  B. Since VLAN 50 has not been assigned to any enabled physical port, the status is down.

  C. VLAN 50 is assigned only to Trunk ports which is why no ports are listed under interfaces.

  D. VLAN 50 was never added to the vlan-database and therefore is in a down state.

  Correct Answer: B

• Question 39:

  Refer to the exhibit.

  

  You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master.

  What is a valid configuration for Access-2 to join the VSF stack?

  A. Access-2# configure Access-2(config)# vsf member 1 Access-2(config)# vsf renumber-to 2 Access-2(vsf-member-1)# link 2 2/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

  B. Access-2# configure Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 2 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

  C. Access-2# configure Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

  D. Access-2# configure Access-2(config)# vsf member 1 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit Access-2(config)# vsf renumber-to 2 This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

  Correct Answer: C

• Question 40:

  Refer to the exhibit.

  

  The above output is the result of issuing the command show system resource-utilization.

  What command should be used to enable terminal output line by line or page by page?

  A. The command page

  B. The command terminal length 30

  C. The command more

  D. The command less

  Correct Answer: A