Juniper Juniper Certifications JN0-361 Questions & Answers

• Question 371:

  Click the Exhibit button An interface is configured as shown in the exhibit.

  

  What must also be configured for this interface to participate in VLAN 100 and 200?

  A. broadcast domains

  B. VLANs

  C. bridge domains

  D. encapsulation type

  Correct Answer: C

• Question 372:

  You are logged into a PE router participating in a Layer 3 VPN as defined in RFC 4364. You would like to ping the remotely connected CE router's loopback address. The address of the loopback is 122.161.2.1, the VPN routing-instance is called VPN-C. Which command will accomplish this goal?

  A. ping instance VPN-C 122.161.2.1

  B. ping routing-instance VPN-C 122.161.2.1

  C. ping VPN-C 122.161.2.1

  D. ping vpn-instance VPN-C 122.161.2.1

  Correct Answer: B

• Question 373:

  Your area border router (ABR) receives type 1.2 and 5 link-state advertisements (LSAs) from a non-backbone area.

  What would the ABR do with the information learned from the non-backbone area?

  A. The ABR will generate type 2 and 3 LSAs and flood type 5 LSAs to the backbone area

  B. The ABR will generate only type 3 LSAs and flood only type 5 LSAs to the backbone area

  C. The ABR will generate type 3 and 4 LSAs. And flood type 5 LSAs to the backbone area

  D. The ABR will generate only type 4 LSAs and flood only type 5 LSAs to the backbone area

  Correct Answer: C

• Question 374:

  Which label operation is performed by an MPLS ingress router?

  A. Pop

  B. Push

  C. Replace

  D. Swap

  Correct Answer: B

• Question 375:

  An RSVP LSP in your network is operational but you are receiving complaints about network throughput across the LSP. You suspect that the RSVP bandwidth was omitted from the router configuration.

  Which operational mode command will help you verify your suspicions?

  A. show interfaces terse

  B. show mpls lsp extensive

  C. show rsvp neighbor detail

  D. show rsvp bandwidth

  Correct Answer: B

• Question 376:

  After configuring OSPF between two routers you check for an adjacency. You see that the adjacencies are not coming up on an Ethernet segment.

  What are two reasons that would cause this situation? (Choose two)

  A. You have a mismatched IP subnet/mask

  B. Your hello timer intervals are mismatched

  C. You are not using the same Junos version on each side

  D. You priority values are mismatched

  Correct Answer: AB

• Question 377:

  What is contained in an IS-IS CSNP message?

  A. all of the headers of the LSPs in a router's link-state database

  B. all of the IP routes in a router's link-state database

  C. all of the IP routes in a router's routing table

  D. all of the LSPs in a router's link-state database

  Correct Answer: A

• Question 378:

  You want to configure support for an IPv6 environment In which hierarchy would you configure an OSPF area?

  A. [edit protocols ospf-v6]

  B. [edit protocols ipv6-ospf

  C. [edit protocols ipv6J

  D. [edit protocols ospf3]

  Correct Answer: D

• Question 379:

  Which action does the local router take after sending a Notification message to a remote peer?

  A. It begins to send route update information

  B. It tears down the TCP session and attempts to re-establish it

  C. It waits for the remote router to acknowledge that it is ready to receive routes

  D. It changes its local state to Established

  Correct Answer: B

• Question 380:

  You have been asked to configure and assign addresses for your IPv6 routers in your network using dynamic assignment of DNS servers. You do not want the MAC address included as part of the IPv6 address.

  Which method of address assignment would accomplish these requirements?

  A. DHCP

  B. stateless auto configuration

  C. DHCPv6

  D. stateful auto configuration

  Correct Answer: C