-- Exhibit -interfaces { ge-1/0/3 { unit 0 {
family inet {
address 192.168.1.1/30;
}
}
}
ge-1/1/0 {
unit 0 {
family inet {
address 10.100.10.1/30;
}
}
}
fxp0 {
unit 0 {
family inet {
address 10.2.1.13/28;
}
}
}
lo0 {
unit 0 {
family inet {
address 10.100.1.1/32;
address 127.0.0.1/32;
}
}
}
}
protocols {
ospf {
area 0.0.0.0 {
interface ge-1/0/3.0;
interface ge-1/1/0.0;
}
}
}
-- Exhibit -
Click the Exhibit button.
The router was just powered on.
Referring to the exhibit, what is the OSPF RID?
A. 192.168.1.1
B. 10.100.1.1
C. 127.0.0.1
D. 10.2.1.13
-- Exhibit -protocols {
isis {
level 1 disable;
interface ge-1/0/0.0 {
level 2 disable;
}
interface ge-1/1/0.0;
interface lo0.0;
} } -- Exhibit -
Click the Exhibit button.
Referring to the exhibit, what is the resulting behavior on interface ge-1/0/0?
A. Level 1 is enabled.
B. Level 1 is disabled.
C. Level 2 is enabled.
D. Level 1 and Level 2 are disabled.
-- Exhibit -user@R1> show configuration interfaces ge-1/1/0
unit 0 {
family inet {
address 10.100.1.1/24 {
vrrp-group 1 {
virtual-address 10.200.12.254;
priority 150;
accept-data;
track {
interface ge-1/0/0 {
priority-cost 40;
}
}
}
}
}
}
user@R2> show configuration interfaces ge-1/1/0
unit 0 {
family inet {
address 10.100.1.2/24 {
vrrp-group 1 {
virtual-address 10.200.12.254;
accept-data;
}
}
}
}
-- Exhibit -
Click the Exhibit button.
R1 and R2 are using VRRP for high availability.
Referring to the exhibit, which two statements are correct about the configuration? (Choose two.)
A. R2 is the backup router and will become the master router if ge-1/0/0 on R1 goes down.
B. R2 is the backup router and will remain the backup router if ge-1/0/0 on R1 goes down.
C. If R1 goes down, R2 will become the master and will relinquish mastership once R1 comes back online.
D. If R1 goes down, R2 will become the master and will remain the master once R1 comes back online.
-- Exhibit -{master}[edit]
user@router-RE0# run show task replication
Stateful Replication: Enabled
RE modE. Master
Protocol Synchronization Status
OSPF Complete
RIP Complete
BGP Complete
MPLS Complete
LDP Complete
{master}[edit]
user@router-RE0# run show bgp summary | find 192.168.1.1
192.168.1.1 65056 0 0 11:14 Establ inet.0: 0/0/0/0 inet.2: 0/0/0/0 bgp.l3vpn.0: 0/0/0/0 ...
{backup}[edit]
user@router-RE1# run show system switchover
Graceful switchover: On
Configuration databasE. Ready
Kernel databasE. Synchronizing
Peer statE. Steady State
{backup}[edit]
user@router-RE1# run show bgp summary | find 192.168.1.1
192.168.1.1 65056 306 581 0 7 7 Idle -- Exhibit -
Click the Exhibit button.
You have been asked to determine if an NSR switchover will be hitless for a given BGP peer.
Referring to the exhibit, which statement is true?
A. The BGP session is idle on the backup RE indicating that the session will flap at switchover.
B. The task replication process has completed on the master indicating a hitless switchover can be expected.
C. The GRES synchronization process is underway and must complete before the protocol state can be checked.
D. The BGP session is idle on the backup RE which is normal; it toggles to established at mastership change.
-- Exhibit -[edit] user@router# show routing-options rib-groups { test { import-rib [ walter.inet.0 nancy.inet.0 ]; } } -- Exhibit -
Click the Exhibit button.
Referring to the exhibit, what is the result of the RIB group configuration?
A. All routes from the walter.inet.0 and the nancy.inet.0 routing tables will be imported into the default master routing instance.
B. Routes from the walter.inet.0 routing table will be imported into the nancy.inet.0 routing table.
C. All routes will be shared between the walter.inet.0 and the nancy.inet.0 routing tables.
D. Routes from the nancy.inet.0 routing table will be imported into the walter.inet.0 routing table.
-- Exhibit -{master}[edit]
user@router-RE0# run show task replication
Stateful Replication: Enabled
RE modE. Master
Protocol Synchronization Status
OSPF Complete
RIP Complete
BGP Complete
MPLS Complete
LDP Complete
{master}[edit]
user@router-RE0# run show bgp summary | match 192.168.1.1
192.168.1.1 65056 288 327 0 2 1:05 Establ
{backup}[edit]
user@router-RE1# run show system switchover
Graceful switchover: On
Configuration databasE. Ready
Kernel databasE. Ready
Peer statE. Steady State
{backup}[edit]
user@router-RE1# run show bgp summary | find 192.168.1.1
192.168.1.1 65056 592 737 3778 2 1:33 Establ
{backup}[edit] user@router-RE1# run show bgp replication Synchronization master: Session statE. Up, SincE. 6d 20:42:51 Flaps: 1, Last flap reason: Commit-sync error Protocol statE. Idle, SincE. 5d 19:41:52 Synchronization statE. Complete Number of peers waitinG. AckWait: 0, SoWait: 0, ScheduleD. 0 rsync walk at: inet.0 - , queued 0 Messages sent: Open 1, Establish 7415, Update 17, Error , Complete 48 Messages receiveD. Open 1, Request 1 wildcard 47 targeted, EstablishAck 2827, CompleteAck 4 -- Exhibit -
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
A. An RE switchover is likely to result in BGP disruption, but no dataplane impact will be seen.
B. An RE switchover is likely to result in BGP disruption which will also effect the dataplane.
C. The system is not yet GRES ready, you need to wait for kernel synchronization to complete.
D. The system is NSR ready and a switchover should be hitless to the BGP control and data plane.
-- Exhibit -[edit policy-options]
user@router# show
policy-statement load-balance {
from {
route-filter 10.243.0.0/24 exact;
route-filter 10.224.1.0/24 exact;
}
then {
load-balance per-packet;
}
}
-- Exhibit -
Click the Exhibit button.
You have been asked to configure per-packet load balancing.
Referring to the exhibit, which configuration correctly applies the load-balancing policy?
A. [edit routing-options] user@router# show forwarding-options { export load-balance; }
B. [edit routing-options] user@router# show static { export load-balance; }
C. [edit routing-options] user@router# show forwarding-table { export load-balance; }
D. [edit routing-options] user@router# show routing-table { export load-balance; }
-- Exhibit -user@router> show route 0/0 exact detail inet.0: 14 destinations, 14 routes (14 active, 0 holddown, 0 hidden)
0.0.0.0/0 (1 entry, 1 announced) *Aggregate PreferencE. 130 Next hop typE. Router, Next hop index: Next-hop reference count: 4 Next hop: 172.30.25.1 via ge-0/0/1.100, selected StatE. Local AS: 65400 AgE. 1:03:46 Task: Aggregate Announcement bits (2): 0-KRT 2-OSPF AS path: I Flags: Generate Depth: 0 Active Contributing Routes (1): 10.0.0.0/16 proto BGP -- Exhibit -Click the Exhibit button.
You are advertising the route in the exhibit to your OSPF neighbors.
What happens if the 10.0.0.0/16 route is unavailable?
A. The default route will remain active and will "blackhole" all traffic from your OSPF peers.
B. The default route will become unavailable and will no longer be advertised to your OSPF peers.
C. The default route will remain active and will continue to be advertised to your OSPF peers.
D. The default route will become unavailable and will continue to be advertised to your OSPF peers.
Which two support tunneling for non-IP protocols on Junos devices? (Choose two.)
A. ATM AAL2
B. GRE
C. IP-IP
D. ATM AAL1
Which two support the tunneling of IP traffic on Junos devices? (Choose two.)
A. ATM AAL2
B. GRE
C. IP-IP
D. ATM AAL1
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Juniper exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your JN0-361 exam preparations and Juniper certification application, do not hesitate to visit our Vcedump.com to find your solutions here.