A new AFF8200 has a four-port UTA2 adapter installed in slot 2. Using the ucadmin command, you see
that these ports are configured for FC.
Which port names are correct in this scenario?
A. e0a/0a, e0b/0b, e0c/0c, e0d/od
B. e2a/2a, e2b/2b, e2c/2c, e2d/2d
C. e2a, e2b, e2c, e2d
D. 2a, 2b, 2c, 2d
You install and apply the NetApp RSCF on cluster interconnect switches.
Which two statements are correct in this scenario? (Choose two.)
A. The RCF file enables jumbo frames for all cluster traffic.
B. The RCF file enables IPv6 for use by the cluster traffic.
C. The RCF file enables flow control and is set to receive.
D. The RCF file enables CDP to allow connected devices to discover the switch.
After setting up a new cluster, you run an AutoSupport message for a test.
Which two commands would you use to proof the functionality and settings of AutoSupport? (Choose two.)
A. system node autosupport show
B. system node autosupport history show
C. system node autosupport option show
D. system node autosupport show history
Config Advisor reports that you have a single point of failure on a stack of shelves. After investigation, you have assigned the following ports to each stack:
stack 1 - ports 0a and 0b stack 2 - ports 3a and 4b stack 3 - ports 4a and 3b
In this scenario, which two changes would you make to the cabling to solve the problem? (Choose two.)
A. Cable stack 3 to ports 4a and 0b.
B. Cable stack 2 to ports 4a and 4b.
C. Cable stack 1 to ports 0a and 3b.
D. Cable stack 3 to ports 3a and 3b.
Which tool would help you to verify an installation of an ONTAP cluster?
A. NetAppDocs
B. OnCommand Insight
C. Config Advisor
D. OnCommand Unified Manager
Which two commands verify that AutoSupport is working as expected?
A. autosupport test show
B. autosupport history show
C. autosupport check show D. autosupport show
You are installing a pair of Cisco Nexus 3132Q-V cluster switches and receive several syntax errors when the reference configuration file (RCF) is applied.
In this scenario, what are two reasons for these errors? (Choose two.)
A. An RCF file for a different version has been loaded.
B. The switch was not in maintenance mode.
C. The RCF was already applied.
D. Cables were not removed before applying the RCF.
You install a new 2-node FAS8200 switchless cluster. You want to reach all necessary management LIFs and SPs for this cluster.
How many management IP addresses do you need in this scenario?
A. 4
B. 5
C. 2
D. 1
You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager.
In this scenario, what caused this problem?
A. Breakout cables were used and the second port on the same ASIC became disabled.
B. This is a hardware error and you must open a case with NetApp Support.
C. You must first enable the ports using the network port modify command.
D. You are missing a license to enable those ports.
You are asked to installed a new cluster with six FAS8060 nodes. While running Config Advisor, you determine that there is a newer firmware version for 16 HDDs.
How should this situation be handled?
A. Prior to leaving the site, advise the customer that firmware is included with the version of ONTAP they selected.
B. Unless the customer advises otherwise, upgrade the firmware on the HDDs to correct the Config Advisor error.
C. Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.
D. Prior to leaving the site, confirm the version of ONTAP that the customer wanted installed to correct the Config Advisor error.
Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only NetApp exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your NS0-182 exam preparations and NetApp certification application, do not hesitate to visit our Vcedump.com to find your solutions here.