Exam Details

  • Exam Code
    :NS0-593
  • Exam Name
    :NetApp Certified Support Engineer ONTAP Specialist
  • Certification
    :NCSE
  • Vendor
    :NetApp
  • Total Questions
    :60 Q&As
  • Last Updated
    :Dec 13, 2024

NetApp NCSE NS0-593 Questions & Answers

  • Question 1:

    You have connection Issues from a Linux host to an AFF A400 FC LUN. You are asked by support to run the NetApp sanlun command to provide troubleshooting information.

    Which NetApp software package must be installed on the host?

    A. Virtual Storage Console

    B. Inventory Collect Tool

    C. Host Utilities package

    D. SnapDrive for UNIX

  • Question 2:

    You recently discovered the error message shown below in your ONTAP logs.

    What should be your first action to correct this Issue?

    A. Power cycle all the disk storage shelves that contain drives of the aggregate with the my_data_vol volume.

    B. Determine the root cause behind the inconsistency before attempting any recovery procedure.

    C. Use the storage takeover command on the storage controller that contains my_data_vol.

    D. Use the wafliron command against my_data_vol to solve the inconsistency on the volume.

  • Question 3:

    A customer reports that while Installing Windows updates on their external Vscan servers, clients couldnot access any files on their CIF-S SVM. The problem disappeared after the update process was completed. The customer wants to prevent this issue from happening during the next patch window.

    In this scenario, what are two ways to accomplish this task? (Choose two.)

    A. Enable the -scan-mandatory flag in the Vscan policy.

    B. Update the Vscan servers one at a time.

    C. Modify the CIFS shares to be continuously available (CA) shares.

    D. Disable the -scan-mandatory flag in the Vscan policy.

  • Question 4:

    When an administrator tries to create a share for an existing volume named voll, the process fails with an error.

    Referring to the exhibit, what Is the reason for the error?

    A. The volume must have a type of DP.

    B. The volume has not beenmounted.

    C. The CIFS service is not authenticating properly with the domain controller.

    D. The CIFS service is not in workgroup mode.

  • Question 5:

    Your customer has mounted an NFS SVM from a Linux client unci performance is very poor. The customer is certain that they have jumbo frames enabled. They have verified an MTU of 9000 on both the Linux client and the broadcast domain on the NetApp ONTAP 9.8 cluster.

    Referring to the exhibit, which ONTAP command will help isolate a possible MTU mismatch?

    A. Option A

    B. Option B

    C. Option C

    D. Option D

  • Question 6:

    You ate connecting a Windows Server 2019 hostto ISCSI LUNs on a 4-node AFF A250 cluster running NetApp ONIAP 9.8 software. The host is unable to connect to the target interface, and the ONTAP event log has the message shown

    below.

    ISCSI: network interface identifier disabled for use; incoming connection discarded

    In this scenario, what is the cause of this connection issue?

    A. iSNS is not enabled on the storage virtual machine.

    B. The WWPN was not added to the initiator group.

    C. The iSCSI service is not enabled on the interface.

    D. CHAP isnot configured correctly for the specified initiator.

  • Question 7:

    A customer's storage administrator Informs you about the deactivated Automatic Switchover (AUSO) feature on their MetroCluster IP environment. What Information would you tell your customer in this scenario?

    A. The AUSO feature cannot be activated due to a non-mirrored aggregate.

    B. The AUSO feature is not available in Metrocluster IP installations by design.

    C. A faulty link automatically deactivated the AUSO feature.

    D. This is a configuration failure, you can activate that feature for the customer.

  • Question 8:

    A customer with an FC MetroClusterconfiguration that is running NetApp ONTAP 9.8 software experienced a site outage and wants to know why the MetroClusler configuration did not switch over to the other site. What are two reasons for this problem? (Choose two.)

    A. There was a failed PSU inthe switchover site.

    B. The ISLs were down between the sites.

    C. The site had unmirrored aggregates.

    D. An ISL link was not operating at 16Gbps.

  • Question 9:

    A customer calls you to troubleshoot a network issue. The customer wants to create a packet trace for allclients on the 192.168.9.0/24 subnet.

    Referring to the exhibit, on which interface do you have to run the packet trace?

    A. a0a-322

    B. e2a-100

    C. e2a-1092

    D. a0a-456

  • Question 10:

    You are deploying NetApp ONTAP Select. When trying to add VMware vCenter to the inventory, you receive the message shown below.

    Credential authentication failed for x.x.x.x with: HostConnectionFailed

    In this scenario, how would you correct this problem?

    A. Change the vCenter password.

    B. Change the IP address of the ONTAP Select Deploy VM.

    C. Change the gateway address of the ONTAP Select Deploy VM.

    D. Change the IP address of the vCenter server.

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only NetApp exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your NS0-593 exam preparations and NetApp certification application, do not hesitate to visit our Vcedump.com to find your solutions here.