Cisco CCNP Data Center 350-601 Questions & Answers

• Question 131:

  Which configuration implements static ingress replication?

  A. interface nve 1 member vni 2100980 ingress-replication protocol static peer-ip 10.0.0.4

  B. interface nve 1 member vni 127772151 ingress-replication protocol bgp

  C. interface nve 1 member vni 3126980 peervtep 10.0.0.4 ingress-replication protocol static peer-ip 10.0.0.4

  D. interface nve 1 member vni 384233213 peer vtep 10.0.0.41

  Correct Answer: A

• Question 132:

  What is a recommended design choice in a topology for multipathing iSCSI traffic?

  A. single initiator to dual targets

  B. initiators and targets in separate subnets

  C. dual initiators to a single target with bonded interfaces

  D. two NICs bended together on the initiator

  Correct Answer: B

  You can create multiple paths by configuring multiple ports and target portals on different IP subnets. By keeping initiator and target ports in different subnets, you can force ESXi to create paths through specific ports. In this configuration, you

  do not use port binding because port binding requires that all initiator and target ports are on the same subnet.

  Reference:

  https://docs.vmware.com/en/VMware-vSphere/7.0/com.vmware.vsphere.storage.doc/GUID-4C19E34E-764C-4069-9D9F-D0F779F2A96C.html

• Question 133:

  Which Cisco network assurance engine feature helps reduce the need for Tier 1 network operation centers to escalate issues?

  A. detailed TCAM optimization

  B. DVR audit trails

  C. operator playbooks

  D. detailed runbooks

  Correct Answer: D

  https://www.cisco.com/c/en/us/products/collateral/data-center-analytics/network-assurance- engine/at-a- glance-c45-740230.html

  

• Question 134:

  A customer wants to offload some of its order processing to a public cloud environment. The customer environment is based on Cisco ACI and uses Puppet with containenzed applications. The operations team requires a solution to orchestrate and optimize the cost of the new solution. Which product must be used to meet these requirements?

  A. Cisco Intersight

  B. Cisco Workload Optimization Manager

  C. Cisco CloudCenter

  D. Cisco Data Center Network Manager

  Correct Answer: C

  https://www.cisco.com/c/dam/en/us/products/collateral/cloud-systems-management/cloudcenter/white-paper-c11-737224.pdf

  -

  Enforce multicloud governance by guiding user decisions to reduce risk

  -

  Securely automate deployment to reduce manual effort and get consistent results

  -

  Increase feature velocity via integration with developer tools to accelerate time to market (CI/CD = Puppet, Chef, and Ansible).

  -Optimize cloud consumption to cut pay-per-use cloud costs https://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/cloudcenter-suite/datasheet-c78-741886.html

• Question 135:

  An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before importing it to a target fabric interconnect. Which backup type must be selected to meet these requirements?

  A. all configuration

  B. system configuration

  C. logical configuration

  D. full state

  Correct Answer: B

  https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Admin- Management/3-1/b_Cisco_UCS_Admin_Mgmt_Guide_3_1/ b_Cisco_UCS_Admin_Mgmt_Guide_3_1_chapter_01001.html

  

• Question 136:

  What is an advantage of NAS compared to SAN?

  A. It provides lossless throughput

  B. It functions in an existing IP environment

  C. It offers enhanced NFS features

  D. It offers enhanced security features.

  Correct Answer: B

• Question 137:

  A Cisco MDS 9000 Series Switch is configured for SAN Analytics and SAN Telemetry Streaming. An engineer must enable analytics for NVMe on interfaces in the range of fc1/1-12. Due to a large amount of traffic generated in the SAN environment, the data must be collected at regular intervals of 60 seconds from ports fc1/1-12 and then for ports fc1/13-24 for the next 60 seconds. Ports in the range fc1/13-24 were already enabled for analytics.

  Which set of commands must be used to meet these requirements?

  

  A. Option A

  B. Option B

  C. Option C

  D. Option D

  Correct Answer: B

  Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/8_x/config/san_analytics/cisco-mds9000-san-analytics-telemetry-streaming-config-guide-8x/configuring_san_telemetry-streaming.html

• Question 138:

  The Cisco Nexus 5600 Series Switch experiences occasional packet drops on interface ethernet 1/16. An engineer wants to implement a SPAN session to investigate the issue further. The network analyzer to which the packets must be directed is located on interface 1/3. The analyzer is limited on disk space available for traffic capture, so the Nexus switch should send only the relevant data.

  Which two command sets configure the SPAN session that meets these requirements? (Choose two.)

  

  A. Option A

  B. Option B

  C. Option C

  D. Option D

  E. Option E

  Correct Answer: BC

  https://www.cisco.com/c/en/us/products/collateral/switches/nexus-5000-series-switches/white- paper-c11- 733022.html https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus6000/sw/system_management/6x/b_6k_System_Mgmt_Config_6x/b_6k_System_Mgmt_Config_602N11_chapter_01111.pdf

  The information to be sent is regarding dropped packets only.

  

• Question 139:

  An engineer configures a role for a new user in Cisco UCS Manager The role should allow the user to configure vHBAs, vNICs, and server port types. Which role should be assigned to allow the engineer to complete this task?

  A. network administrator

  B. operations

  C. server-compute

  D. AAA administrator

  Correct Answer: A

  Network Administrator

  Read-and-write access to fabric interconnect infrastructure and network security operations. Read access to the remaining system.

  Server Compute

  Read and write access to most aspects of service profiles. However, the user cannot create, modify or delete vNICs or vHBAs.

• Question 140:

  An engineer must generate a checkpoint of the running configuration on a Cisco Nexus Switch. The checkpoint file name must be called "before_maintenance' and should be used for recovering the switch to its pre-maintenance state. The rollback of the checkpoint to running configuration should only occur if no errors occur. Which two configuration commands must be used to meet these requirements? (Choose two.)

  A. rollback checkpoint file before_maintenance stop-at-first-failure

  B. checkpoint file before_maintenance

  C. checkpoint before_maintenance

  D. rollback running-config file before_maintenance atomic

  E. rollback running-config checkpoint before_maintenance

  Correct Answer: BD

  https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/command/reference/security/ n5k-sec-cr/n5k-sec_cmds_r.html

  rollback checkpoint is invalid command. Rollback should be to running configuration, not a checkpoint rollback can be selected by a name or file name. the difference between them is using the "file" keyword.