Cisco CCNP Data Center 350-601 Questions & Answers

• Question 171:

  An engineer must configure SAN connectivity in Cisco UCS manager. The requirement is to specify the WWPN of the storage array and set the zoning type to single initiator multiple targets. The engineer must also configure interrupt handling and queues of the vHBA interface. Which two Cisco UCS policies should be used to configure the settings? (Choose two.)

  A. SAN connectivity policy

  B. Fibre Channel adapter policy

  C. vHBA policy

  D. boot policy

  E. storage connection policy

  Correct Answer: BE

• Question 172:

  An engineer must perform a nondisruptive software upgrade on a dual supervisor Cisco Nexus 7000 series switch. What is the cause of the upgrade being disruptive?

  A. The show install all impact command is not issued Before the upgrade

  B. The kickstart image is installed by using the install all kickstart image system image command

  C. Attempt to simultaneously upgrade more than three cards

  D. Change of the configuration settings or the network connections during the upgrade process

  Correct Answer: D

• Question 173:

  A network engineer must deploy a configuration backup policy to the cisco UCS manager. The file generated from this backup must have a snapshot of the entire system that should be used to restore the system during disaster recovery. The backup file must be transferred insecurely by using the TCP protocol. Which configuration backup settings meet these requirements?

  

  A. Option A

  B. Option B

  C. Option C

  D. Option D

  Correct Answer: B

• Question 174:

  DRAG DROP

  Drag and drop the network assurance concepts from the left onto the corresponding benefits on the right.

  Select and Place:

  

  Correct Answer:

  

• Question 175:

  DRAG DROP

  

  Refer to the exhibit. An engineer must monitor the Ethernet port and the corresponding VLAN traffic for the hyper4 device The SW3 device is a Cisco Nexus 7000 Series Switch. Drag and drop the code snippets from the right into the boxes in the configuration to meet these requirements.

  Select and Place:

  

  Correct Answer:

  

• Question 176:

  DRAG DROP

  

  Refer to the exhibit. The Cisco Nexus Series Switches SW1, SW2, and SW3 are connected via Layer 2 copper interfaces. An engineer implements loop prevention standard IEEE 802.1w on each VLAN lo provide lasier recovery from network changes or failures. The Implementation has these requirements:

  1.

  Interfaces that are connected to Layer 2 hosts must not receive STP BPDUs.

  2.

  The implementation must detect unidirectional links due to one-way traffic twisted- pair links

  3.

  Bridge assurance must be enabled between SW2 and SW3 The Layer 2 domain must be protected from superior BPDUs that arrive from external switches.

  Drag and drop the code snippets from the right onto the blanks in the code on the left to complete the configuration for SW3. Not all code snippets are used.

  Select and Place:

  

  Correct Answer:

  

  interface ethernet 1/4 spanning-tree port type network udld aggressive interface ethernet 1/5 spanning-tree guard root interface ethernet 1/6 spanning-tree port type edge

  In the question, we have 4 most important requirements:

  1.

  Interfaces that are connected to Layer 2 hosts must not receive STP BPDUs.

  2.

  The implementation must detect unidirectional links due to one-way traffic twisted-pair links.

  3.

  Bridge assurance must be enabled between SW2 and SW3.

  4.

  The Layer 2 domain must be protected from superior BPDUs that arrive from external switches. 1st: command spanning-tree port type edge disables stp process on port 2nd: udld aggressive enables UDLD in aggressive mode 3rd: Bridge assurance is enabled globally by default on NX-OS. However, we do have to change the spanning-tree port type to network on interfaces 4th: Root guard is enabled with the interface command spanning-tree guard root. Root guard is placed on designated ports toward other switches that should never become root bridges.

• Question 177:

  DRAG DROP

  A network administrator must automate the process of pinging all the IP addresses from the 10.0.0.0/8 subnet. The subnet is already present on the ARP table of the Cisco Nexus switch.

  Drag and drop the bash commands to generate the desired output. Not all commands are used.

  Select and Place:

  

  Correct Answer:

  

• Question 178:

  DRAG DROP

  An engineer must configure remote authentication on a Cisco UCS system. The user password must be encrypted before it is sent to the authentication server. The company security policy requires the server to be based on an open

  standard.

  Drag and drop the UCS CLI AAA configuration commands from the left into the order in which they must be implemented on the right. Not all commands are used.

  Select and Place:

  

  Correct Answer:

  

• Question 179:

  DRAG DROP

  Drag and drop the firmware packages from the left onto the software bundles they belong to on the right.

  Select and Place:

  

  Correct Answer:

  

• Question 180:

  DRAG DROP

  An engineer must configure HSPR protocol on two Cisco Nexus 9000 Series Switches running a virtual port channel. In addition, the HSRP implementation must meet these requirements:

  It must allow more than 500 groups.

  switch1 must act as the primary switch.

  Both switches must use a user-defined hardware address.

  Drag and drop the commands from the right to complete a configuration of the HSRP on the left. The commands are used more than once. Not all commands are used.

  Select and Place:

  

  Correct Answer: