HP HP ExpertONE Certification HP2-T23 Questions & Answers

• Question 71:

  What is a DDR3 memory population rule to follow for a ProLiant Gen8 server?

  A. UDIMMs, RDIMMs, and LRDIMMs can be mixed in the same bank.

  B. DIMMs of different voltages or speeds cannot be mixed in the same bank.

  C. If only one processor is installed in a two-processor system, only half of the DIMM slots are available.

  D. The server automatically balances capacity of quad-rank RDIMMs across all memory channels.

  Correct Answer: A

• Question 72:

  Which statements are correct about the HP Customer Self Repair (CSR) program?

  A. A travel and labor charge applies when customers request HP to replace parts.

  B. A travel and labor charge does not apply when customers decline to replace a mandatory CSR part.

  C. A travel and labor charge does not apply when customers decline to replace an optional CSR part.

  D. A travel and labor charge applies when customers decline to replace an optional CSR part.

  Correct Answer: A

• Question 73:

  How wide must the a data center door be to allow an HP MCS G2 rack to be brought into the data center?

  A. 45 cm (1.5 feet)

  B. 60 cm (2 feet)

  C. 80 cm (2.5 feet)

  D. 110 cm (3.6 feet)

  Correct Answer: D

• Question 74:

  A support engineer is installing DIMMs of different speeds and voltages in a ProLiant DL380p Gen8 Server. Which rules for DIMM installation must the engineer follow during this installation?

  

  A. Four quad-ranked LRDIMMs are supported across all memory channels. The server balances capacity automatically.

  B. RDIMMs operating at either 1.35V or 1.5V may be mixed in any order. The system will operate at the lower voltage.

  C. DIMMs of different speeds may be mixed in any order. The server will select the lowest common speed.

  D. UDIMMs, RDIMMs, and LRDIMMs may be mixed in the same bank in the server if only one processor is installed.

  Correct Answer: BC

• Question 75:

  What do you need to manage and control an InfiniBand fabric?

  A. Asubnet manager

  B. Amezzanine connector

  C. System Management Homepage

  D. Version Control Agent

  Correct Answer: A

• Question 76:

  Which statements are correct about HP Systems Insight Manager (HP SIM) 7.0 Agentless Management? (Select two.)

  A. HP SIM communicates with the CPU and collects essential data for the operating system.

  B. Agentless Management is provided by the CPU.

  C. HP SIM communicates with the iLO Management Engine to collect hardware data.

  D. The Agentless Management Service runs on the host to provide software information directly to the iLO Management Engine.

  Correct Answer: CD

• Question 77:

  The system ROM is causing memory errors in a customer's mission-critical server blade. After you update the system ROM in this server blade, how can you confirm that the other server blades in the enclosure have the correct system ROM?

  A. Use telnet to connect to the Onboard Administrator and enter show server version all.

  B. Use PuTTY to connect to the Onboard Administrator and enter show all.

  C. Browse to the Onboard Administrator, hover over the iLO and check the version.

  D. Tell the customer to power the server down so you can view the POST message.

  Correct Answer: B

• Question 78:

  How do you boot into Intelligent Provisioning on a ProLiant Gen8 server?

  A. by pressing the F9 button during POST

  B. pressing the F10 button during POST

  C. through a Scripting Toolkit server configuration script

  D. through the Array Configuration Utility (ACU) in offline mode

  Correct Answer: B

• Question 79:

  From which location does Active Health collect data?

  A. iLO

  B. SMH

  C. Event Log

  D. IML

  Correct Answer: A

• Question 80:

  An administrator must replace a defective processor located in slot 1 in an Intel-based ProLiant DL5860 Gen8 server:

  What should the administrator do?

  A. Install the second processor in slot 1.

  B. Confirm that processor memory board 1 is installed before removing the processor.

  C. Open the fan cage before removing the processor.

  D. Open the heat sink retaining bracket to remove the processor.

  Correct Answer: D