HP HP Certifications HPE6-A41 Questions & Answers

• Question 41:

  A network administrator uses the console to access an ArubaOS core switch and wants to find the management IP address of another ArubaOS switch that is currently connected to port B1. Which information should the administrator review?

  A. interface with the use of the show interface command

  B. LLDP with the use of the show lldp info remote-device command

  C. ARP with the use of the show arp command

  D. device profile with the use of the show device-profile status command

  Correct Answer: B

• Question 42:

  An interface on an ArubaOS switch did not receive any BDPUs and has the spanning tree auto-edge setting. What describes the effect of this setting?

  A. The interface has spanning tree disabled on it and ignore BPDUs.

  B. The interface remains forwarding during topology changes.

  C. The interface root path cost is automatically set to 0.

  D. The interface is preferred to be selected as master port.

  Correct Answer: B

• Question 43:

  Refer to the exhibit.

  

  The student A client needs to connect to FTP Server B. Student A sends the necessary ARP request and receives a reply.

  Which destination MAC address does the Student A client use in the FTP packet to FTP Server B?

  A. 00-1D-B3-F1-EF-40

  B. 00-E0-52-F0-44-87

  C. 00-1D-B3-F1-EF-31

  D. 00-E0-52-F0-41-B2

  Correct Answer: A

• Question 44:

  What is a requirement for links to successfully participate in an aggregated link?

  A. that links have the spanning tree protocol disabled

  B. that links use the same speed and duplex mode

  C. that links use the same media type and are untagged

  D. that links are untagged and are associated to the same VLAN

  Correct Answer: B

• Question 45:

  An ArubaOS switch provides PoE+ to several Aruba APs. Users might also connect PoE devices to this switch. In a situation where the switch PoE capacity is exceeded, the network administrator wants to ensure that the switch continues to power the APs in preference to other devices.

  What should the administrator do to achieve this goal?

  A. Set the PoE priority for the ports connected to APs to critical.

  B. Set the PoE class for the ports connected to APs to Class 5.

  C. Make sure that LLDP MED is enabled on both the switch ports and the APs.

  D. Set the PoE allocation on the ports connected to APs to the maximum value permitted by PoE+.

  Correct Answer: A

• Question 46:

  What is a valid setup for a Virtual Switching Framework (VSF) fabric?

  A. one 5406R zl2 switch as commander and one 5412R zl2 switch as a standby member

  B. one 5412R zl2 switch as commander and two 5406R zl2 switches as standby members

  C. one 5406R zl2 switch as commander and two 5412R zl2 switches as standby members

  D. one 5412R zl2 switch as commander and one 5412R zl2 switch as a standby member

  Correct Answer: D

• Question 47:

  Refer to the exhibit.

  

  Prior to implementing OSPF on the network, an ArubaOS switch had the IP routing table shown in the exhibit.

  The network administrator then sets up OSPF in the network. The switch calculates these OSPF routes to 10.1.20.0/24:

  Through 10.1.0.1 with cost 2 and administrative distance 110 Through 10.1.0.2 with cost 3 and administrative distance 110 Through 10.1.0.3 with cost 4 and administrative distance 110 How does the switch now handle traffic that is destined to the 10.1.20.0/24 network?

  A. It sends all of the traffic to 10.1.0.3.

  B. It load balances the traffic: sends some to 10.1.0.1 and some to 10.1.0.3.

  C. It load balances the traffic: sends some to 10.1.0.2 and some to 10.1.0.3.

  D. It sends all of the traffic to 10.1.0.1.

  Correct Answer: A

• Question 48:

  Refer to the exhibit.

  

  The link between Core-1 and Core-2 shown in the exhibit fails, and some users lose connectivity. What should the network administrator do to prevent this issue in a situation such as this?

  A. Configure BPDU protection on all Core-2 ports.

  B. Enable IP routing on Core-2.

  C. Create routes to 10.1.10.0/24 and 10.1.11.0/24 through 10.1.1.3 on Core-2.

  D. Extend VLANs 10 and 11 on all switch-to-switch links.

  Correct Answer: D

• Question 49:

  A network administrator wants to place desktops connected to an ArubaOS switch in VLAN5. The desktops have no awareness of VLANs. How should the administrator assign desktops to the VLAN?

  A. Make switch ports connected to desktops tagged members of VLAN5.

  B. Make VLAN5 the Default VLAN on the switch before the desktops connect to the switch ports.

  C. Make VLAN5 the Primary VLAN on the switch.

  D. Make switch ports connected to desktops untagged members of VLAN5.

  Correct Answer: D

• Question 50:

  A network administrator connects an Aruba Instant AP (IAP) to an ArubaOS switch but cannot connect the AP to the Instant cluster that exists. The administrator wants to check the IAP management IP address and software version from the ArubaOS switch CLI. To obtain this information, what should the administrator ensure is enabled on the switch and switch interfaces?

  A. SNMP

  B. ARP

  C. Device profiles

  D. LLDP

  Correct Answer: D