HP HP Certifications HPE6-A71 Questions & Answers

• Question 151:

  Refer to the exhibit.

  An administrator wants to verify the operation of MultiZone in a network. The administrator uses the

  command show ap debug multizone to generate the output shown in the exhibit.

  Based on the output, which statement is true?

  

  A. Zone 1 is the primary zone, and zone 0 is the data zone.

  B. The primary zone has limited the data zone to one WLAN.

  C. The maximum VAPs in the MultiZone is 15.

  D. The MultiZone APs are in a cluster.

  Correct Answer: B

• Question 152:

  Refer to the exhibit.

  

  An administrator implements AP licensing on a Mobility Master (MM).

  Network engineers at CampusA want to deploy an additional 100 APs. Currently all of the AP licenses in

  CampusA and CampusB are allocated, but only 200 of the AP licenses in CampusC are allocated.

  Each campus is responsible to purchase its own AP licenses. There are 900 AP licenses deployed in the

  global pool.

  There are three dedicated pools.

  From the global pool, 300 AP licenses are assigned to each dedicated pool.

  What can the administrator do to add capacity for CampusA in alignment with campus policies?

  A. Allow CampusA to share from the CampusC pool.

  B. Add 100 more AP licenses and assign them to the CampusA pool.

  C. Move 100 licenses from the CampusC pool to the global pool.

  D. Add 100 more AP licenses to the global pool.

  Correct Answer: C

• Question 153:

  Which Aruba AP mode constantly scans the radio environment to gather IDS and RF information?

  A. Spectrum AP

  B. RAP

  C. Mesh Portal

  D. Air Monitor

  Correct Answer: D

• Question 154:

  An administrator implements the MultiZone feature and uses two clusters that utilize CPSec. A primary and a data zone are created. MultiZone APs successfully build sessions to the primary cluster but fail to

  establish sessions to the data zone cluster. What must the administrator do to solve this problem?

  A. Enable CPSec in the MultiZone profile for both the primary and data zone.

  B. Enable MultiZone booting in the MultiZone AP apboot configuration mode.

  C. Add the MultiZone APs to the data zone's CPSec whitelist.

  D. Use different AP Group names for the two zones.

  Correct Answer: C

• Question 155:

  An administrator creates new pre-and post-authentication roles for a new WLAN. For which profile should the administrator assign these new roles under the Managed Network section?

  A. Server Groups

  B. Virtual AP

  C. 802.1X

  D. AAA profile

  Correct Answer: D

• Question 156:

  An administrator deploys an AP at a branch office. The branch office has a private WAN circuit that provides connectivity to a corporate office controller. An Ethernet port on the AP is connected to a network storage device that contains sensitive information. The administrator is concerned about sending this traffic in clear-text across the private WAN circuit.

  What can the administrator do to prevent this problem?

  A. Redirect the wired port traffic to an AP-to-controller GRE tunnel.

  B. Convert the campus AP into a RAP.

  C. Enable AP encryption for wired ports.

  D. Enable IPSec encryption on the AP's wired ports.

  Correct Answer: B

• Question 157:

  Which IEEE standard should user devices support to implement Fast BSS Transition when a network implements wireless roaming (mobility)?

  A. 802.11r

  B. 802.11f

  C. 801.11m

  D. 802.11i

  Correct Answer: A

• Question 158:

  Refer to the exhibit.

  

  Two Aruba Mobility Controllers (MC) are managed by a Mobility Master (MM) in a non- cluster deployment

  as shown in the exhibit.

  The C1 controller is connected to AP1 and AP2.

  The C2 controller is connected to AP3 and AP4.

  VLAN mobility is enabled in the VAPs of both AP Groups.

  Both C1 and C2 support the same VLANs.

  User1's wireless device supports BSS Fast Transitioning and is currently connected to AP1.

  What happens if User1 roams across the network and the user's device associates to AP3?

  A. User1's traffic is terminated on the C2 controller, and they will have to re-authenticate and re-obtain a new IP address.

  B. User1's traffic is terminated on the C2 controller, and they will not have to re- authenticate but will need to obtain a new IP address.

  C. User1's traffic is terminated on the C2 controller, and they will have to re-authenticate and can keep their original IP address.

  D. User1's traffic is tunneled to the C1 controller, where they will not have to re- authenticate and can keep their original IP address.

  Correct Answer: D

• Question 159:

  An administrator has a cluster of Aruba Mobility Controllers (MCs). The administrator wants to manually reboot one of the controllers.

  Before rebooting, which command should the administrator use to move the APs?

  A. apmove

  B. lc-cluster move ap

  C. active-ap-rebalance

  D. active-ap-lb

  Correct Answer: A

• Question 160:

  Which protocol is used to tunnel user traffic when an administrator implements tunneled mode between an ArubaOS-Switch and an Aruba Mobility Controller (MC)?

  A. IPSec

  B. AMON

  C. PAPI

  D. GRE

  Correct Answer: D