HP HP ATP HP2-Z30 Questions & Answers

• Question 41:

  A network administrator receives a new HP Provision switch and notices that the software version running on the switch is older than what is currently used in the network. The network administrator copies an updated version of the operating

  system from the new switch's USB port to the secondary flash location. The network administrator then executes the following command:

  Provision# boot system flash secondary:

  The switch reboots using the new operating system. However, when the network administrator turns off the switch and turns it back on, the switch boots from the old operating system.

  Which solution should the network administrator use to fix the problem?

  A. Execute the startup-boot secondary command.

  B. Boot into the switch's Monitor ROM Console and perform the upgrade a second time.

  C. Execute the boot set-default flash secondary command.

  D. Execute the boot-loader file command.

  E. Execute the startup-default secondary command.

  Correct Answer: C

  Explanation: http://hpblogs.lithium.com/t5/HP-Networking/HP-ProCurve-using- multiple-config-files/ba-p/42024#.Uy-5LqiSwkQ

• Question 42:

  Which configuration tool do HP Provision switches support that HP Comware switches do not support?

  A. menu system

  B. auto configuration tool

  C. web-based

  D. SNMP

  Correct Answer: C

• Question 43:

  Refer to the exhibit.

  

  A network administrator is managing the configuration files on an HP Provision switch and executes the commands shown in the exhibit. What is the probable cause of the error message when the network administrator tries to copy the file?

  A. The flash memory in the switch is full and supports no more files.

  B. The copy command should only be used to manage operating systems.

  C. No empty configuration memory slots exist on the switch.

  D. The copy command contains a syntax error.

  Correct Answer: C

• Question 44:

  Which HP redundancy feature is supported by both HP Provision and HP Comware switches?

  A. meshed stacking

  B. distributed trunking

  C. static link aggregation

  D. dynamic LACP

  Correct Answer: C

• Question 45:

  Refer to the exhibit.

  

  The link aggregation is failing between the HP Provision and HP Comware switches. Which solution solves this problem?

  A. The interfaces used for trunking on the Provision switch must be continuous.

  B. The Provision switch must be reconfigured for dynamic LACP

  C. The Comware switch must be reconfigured for static LACP O

  D. The Comware switch must be reconfigured for dynamic LACP.

  Correct Answer: D

• Question 46:

  Which Intelligent Management Center (IMC) device discovery method is the default for device auto discovery?

  A. ARP-based

  B. PPP protocol-based

  C. network segment-based

  D. LDAP-based

  Correct Answer: C

• Question 47:

  Which HP Comware command can a network administrator execute to view the IP routing table?

  A. display ip routing-table

  B. show ip route

  C. show ip routing-table

  D. display ip route

  Correct Answer: A

• Question 48:

  Which command defines a default route on an HP Provision switch when routing has been enabled?

  A. ip route 0.0.0.0/0 10.1.1.1

  B. iP route 0.0.0.0/32 10.1.1.1

  C. ip route 0.0.0.0 0 10.1.1.1

  D. ip default-gateway 10.1.1.1

  Correct Answer: A

• Question 49:

  Refer to the network exhibit.

  

  A user brings a generic switch from home into a company. The user switch does not support any Spanning Tree protocols. The user switch has two connections to the network on switch ports that are defined as edge ports. Assume the company switches are HP Provision switches.

  Which HP protection feature effectively manages this problem?

  A. Edge Protection

  B. Loop Protection

  C. Root Protection

  D. BPDU Protection

  Correct Answer: B

  Explanation: http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/ docDisplay?javax.po rtlet.begCacheTok=com.vignette.cachetokenandjavax.portlet.endCacheTok=com.vignette.ca chetokenandjavax.portlet.prp_ba847bafb2a2d782fcbb0710b053ce01=wsrp-navigationalState %3DdocId%253Demr_na-c02596540-1%257CdocLocale %253D%257CcalledBy %253Dandjavax.portlet.tpst=ba847bafb2a2d782fc bb0710b053ce01andsp4ts.oid=3296367andac.admitted=1395635335914.876444892.1994801

• Question 50:

  Which management protocol is enabled, by default, on HP Provision switches?

  A. Syslog

  B. SSH

  C. SNMP

  D. NTP

  Correct Answer: B